ProForm 1800 user manual

Page 32

SYMPTOM: The walking belt is off-center or slips when walked on

a.If the walking belt is off-center, first remove the key and UNPLUG THE POWER CORD. If the walking belt has shifted to the left, use the hex key to turn the left idler roller screw clockwise 1/2 of a turn; if the walking belt has shifted to the right, turn the left idler roller screw counterclock- wise 1/2 of a turn. Be careful not to overtighten the walking belt. Then, plug in the power cord, insert the key, and run the treadmill for a few minutes. Repeat until the walking belt is centered.

a

b.If the walking belt slips when walked on, first remove the key and UNPLUG THE POWER CORD. Using the hex key, turn both idler roller screws clockwise, 1/4 of a turn. When the walk- ing belt is correctly tightened, you should be able to lift each edge of the walking belt 2 to 3 in. (5 to 7 cm) off the walking platform. Be careful to keep the walking belt centered. Then, plug in the power cord, insert the key, and carefully walk on the treadmill for a few minutes. Repeat until the walk- ing belt is properly tightened.

b

SYMPTOM: The iFit Live mode does not function correctly

a.If the iFit Live mode is not functioning correctly, make sure that the treadmill has the most current firmware available (see step 3 on page 26).

SYMPTOM: The treadmill will not connect to the wireless network

a.Make sure that the wireless settings on your con- sole are correct (see step 4 on page 27).

b.Make sure that the settings for your wireless net- work are correct.

c.If you still have questions, see the front cover of this manual.

32

Image 32

Contents QUESTIONS? Model No. PFTL11011.0 Serial NoCall TOLL-FREE Mon.-Fri a.m.-6 p.m. MT Sat a.m.-4 p.m. MTTable of Contents Important Precautions Page Before YOU Begin Part Identification Chart Assembly Make sure that the power cord is unpluggedAttach the Right Upright not shown See the inset drawing. Tie the wire tieTighten the Screws yet. Note Use the short hex Base Covers into place yet Page Page Console Assembly Make sure to follow all Instructions in this step Raise the Frame 56 to the position shown Press the Grommet 77 into the square hole in the Base Use a Surge Suppressor Operation and AdjustmentHOW to Connect the Power Cord Console DiagramFeatures of the Console HOW to Turn on the Power HOW to USE the Touch ScreenHOW to SET UP the Console Connect to your wireless network Check for firmware updatesCalibrate the incline system Create an iFit Live accountHOW to USE the Manual Mode When you are finished exercising, remove Power cord. Important If you do not doMeasure your heart rate if desired Key from the consoleStart the workout HOW to USE AN Onboard WorkoutSelect an onboard workout HOW to USE a SET-A-GOAL Workout Select the main menu. See on Select a set-a-goal workoutHOW to USE AN Ifit Live Workout Start the workout. See onHOW to USE the Equipment Settings Mode HOW to USE the Maintenance Mode Exit the maintenance modeCalibrate the incline system of the treadmill Find keycodesHOW to USE the Wireless Network Mode Enable Wi-FiSet up and manage a wireless network connection Exit the wireless network modeHOW to USE the Internet Browser HOW to USE the Stereo Sound SystemMake sure that the audio wire is fully plugged HOW to Fold and Move the Treadmill HOW to Fold the TreadmillHOW to Move the Treadmill HOW to Lower the Treadmill for USETroubleshooting Symptom The power turns off during useSymptom The walking belt slows when walked on Page Exercise Guidelines Exercise IntensityWorkout Guidelines Exercise FrequencyPart List Qty DescriptionDescription Qty Exploded Drawing a Exploded Drawing B Exploded Drawing C Exploded Drawing D Icon Health & Fitness, Inc., 1500 S W., Logan, UT Ordering Replacement PartsLimited Warranty