ProForm 1800 user manual Assembly, Make sure that the power cord is unplugged

Page 7

ASSEMBLY

•To hire a service technician to assemble this product in your home, call 1-800-445-2480.

•Assembly requires two persons.

•Place all parts in a cleared area and remove the packing materials. Do not dispose of the packing materials until you finish all assembly steps.

•After shipping, there may be an oily substance on the exterior of the treadmill or on the shipping carton. This is normal. If there is an oily sub- stance on the treadmill, wipe it off with a soft cloth and a mild, non-abrasive cleaner.

•To identify small parts, see page 6.

•Assembly requires the following tools:

the included hex keys one adjustable wrench one Phillips screwdriver a pair of scissors

To avoid damaging parts, do not use power tools.

1. Make sure that the power cord is unplugged.	1
Place a piece of cardboard below the rear of the	1
Place a piece of cardboard below the rear of the
Frame (56) to protect the floor or carpet.
Attach the Left Wheel Cap (96) to the Base (94)
with two #8 x 3/4" Screws (2).		56
		56
Attach the Right Wheel Cap (not shown) to
the right side of the Base (94) in the same
way.	94
	94
	2
		96
		Cardboard
2. Pull the Upright Wire (81) and the base ground	2
wire (A) through the indicated hole in the	2
wire (A) through the indicated hole in the
Base (94).
Attach the base ground wire (A) to the Base (94)
with a #8 x 1/2" Ground Screw (10).	Hole
	Hole
	81
	10	A
	10	94
	7

Image 7

Contents Mon.-Fri a.m.-6 p.m. MT Sat a.m.-4 p.m. MT QUESTIONS?Model No. PFTL11011.0 Serial No Call TOLL-FREETable of Contents Important Precautions Page Before YOU Begin Part Identification Chart Make sure that the power cord is unplugged AssemblyTighten the Screws yet. Note Use the short hex See the inset drawing. Tie the wire tieAttach the Right Upright not shown Base Covers into place yet Page Page Console Assembly Make sure to follow all Instructions in this step Raise the Frame 56 to the position shown Press the Grommet 77 into the square hole in the Base HOW to Connect the Power Cord Operation and AdjustmentUse a Surge Suppressor Features of the Console DiagramConsole HOW to USE the Touch Screen HOW to Turn on the PowerCreate an iFit Live account HOW to SET UP the ConsoleConnect to your wireless network Check for firmware updates Calibrate the incline systemHOW to USE the Manual Mode Key from the console When you are finished exercising, removePower cord. Important If you do not do Measure your heart rate if desiredSelect an onboard workout HOW to USE AN Onboard WorkoutStart the workout Select the main menu. See on Select a set-a-goal workout HOW to USE a SET-A-GOAL WorkoutStart the workout. See on HOW to USE AN Ifit Live WorkoutHOW to USE the Equipment Settings Mode Find keycodes HOW to USE the Maintenance ModeExit the maintenance mode Calibrate the incline system of the treadmillExit the wireless network mode HOW to USE the Wireless Network ModeEnable Wi-Fi Set up and manage a wireless network connectionMake sure that the audio wire is fully plugged HOW to USE the Stereo Sound SystemHOW to USE the Internet Browser HOW to Lower the Treadmill for USE HOW to Fold and Move the TreadmillHOW to Fold the Treadmill HOW to Move the TreadmillSymptom The power turns off during use TroubleshootingSymptom The walking belt slows when walked on Page Exercise Frequency Exercise GuidelinesExercise Intensity Workout GuidelinesQty Description Part ListDescription Qty Exploded Drawing a Exploded Drawing B Exploded Drawing C Exploded Drawing D Limited Warranty Ordering Replacement PartsIcon Health & Fitness, Inc., 1500 S W., Logan, UT