ProForm 2 user manual Troubleshooting, Compatible with GFCI-equipped outlets

Page 25

TROUBLESHOOTING

Most treadmill problems can be solved by following the steps below. Find the problem that applies, and follow the steps listed. If further assistance is needed, please see the front cover of this manual. PROBLEM: The power does not turn on

SOLUTION: a. Make sure that the power cord is plugged into a surge suppressor, and that the surge suppressor

is plugged into a properly grounded outlet (see page 11). Use only a single-outlet surge suppres-

sor that meets all of the specifications described on page 11. IMPORTANT: The treadmill is not

compatible with GFCI-equipped outlets.

 

 

b. After the power cord has been plugged in, make sure that the key is inserted into the console.

c. Check the power switch located on the treadmill frame

c

 

near the power cord. If the switch protrudes as shown,

 

the switch has tripped. To reset the switch, wait for five

Tripped

Reset

minutes and then press the switch back in.

PROBLEM: The power turns off during use

 

 

SOLUTION: a. Check the power switch (see the drawing above). If the switch has tripped, wait for five minutes and then press the switch back in.

b. Make sure that the power cord is plugged in. If the power cord is plugged in, unplug it, wait for five minutes, and then plug it back in.

c. Remove the key from the console. Reinsert the key into the console.

d. If the treadmill still will not run, please see the front cover of this manual.

PROBLEM: The console screen remains lit when you remove the key from the console

SOLUTION: a. The console features a display demo mode, designed to be used if the treadmill is displayed in a

store. If the screen shows a preset presentation when you remove the key, the demo mode is

turned on. To turn off the demo mode, see step 5 on page 21.

PROBLEM: The console does not display speed and distance correctly

SOLUTION: a. Remove the key from the console and UNPLUG THE

a

POWER CORD. Then, place the treadmill in the stor-

age position (see HOW TO FOLD THE TREADMILL

1

on page 24).

Next, remove the two indicated #8 x 3/4" Screws (1).

 

 

1

25

Image 25
Contents Model No. PFTL15010.0 Serial No QUESTIONS?Mon.-Fri a.m.-6 p.m. MT Sat a.m.-4 p.m. MT On the WEBTable of Contents Important Precautions Page Before YOU Begin Wrench AssemblyBolts yet Attach the Left Upright 91 in the same way To pinch the Upright WireWire Tie Console Assembly 110 Assembly Make sure to keep the latch cap inside HOW to Plug in the Power Cord Operation and AdjustmentPRE-LUBRICATED Walking Belt Features of the Console Console DiagramHOW to USE the Manual Mode HOW to Turn on the PowerPage Measure your heart rate if desired Power cord. Important If you do not doThis, the treadmillʼs electrical components may Wear prematurelyStart the workout HOW to USE a SET-A-GOAL WorkoutStart the workout Monitor your progress Connect your treadmill to your own wireless network HOW to USE the Ifit Live ModeSelect the iFit Live mode Ifit Live FCC InformationHOW to USE the Settings Mode HOW to USE the Stereo Sound SystemSelect the settings mode Select the wireless network modeExit the settings mode Change the international settingsLog in to your iFit Live account Calibrate the screen HOW to USE the Maintenance Mode Perform a network test View technical information Exit the maintenance modeHOW to Fold the Treadmill HOW to Fold and Move the TreadmillHOW to Move the Treadmill HOW to Lower the Treadmill for USEProblem The power turns off during use TroubleshootingCompatible with GFCI-equipped outlets Problem The walking belt slows when walked on Problem The iFit Live mode does not function correctlyTop Problem Solution Exercise Intensity Exercise GuidelinesWorkout Guidelines Exercise FrequencyQty Description Part ListDescription Key No. Qty Exploded Drawing a Exploded Drawing B Exploded Drawing C Exploded Drawing D Exploded Drawing E Limited Warranty Ordering Replacement PartsIcon Health & Fitness, Inc., 1500 S W., Logan, UT