ProForm 2 user manual Top, Problem The iFit Live mode does not function correctly

Page 26

Lower the treadmill (see HOW TO LOWER THE

 

 

1

1

TREADMILL FOR USE on page 24). Remove the four

 

75

indicated #8 x 3/4" Screws (1), and remove the Motor

 

 

 

Hood (75).

 

 

 

 

Next, locate the Reed Switch (53) and the Magnet

 

Top

 

 

(58) on the left side of the Pulley (59). Turn the Pulley

 

 

 

until the Magnet is aligned with the Reed Switch.

 

View

 

 

Make sure that the gap between the Magnet and

 

24

 

1/8 in.

the Reed Switch is about 1/8 in. (3 mm). If neces-

 

 

sary, loosen the indicated #8 x 3/4" Tek Screw (24),

 

 

 

59

move the Reed Switch slightly, and then retighten the

 

53

 

Screw. Then, reattach the Motor Hood (not shown)

 

 

58

with the six #8 x 3/4" Screws (not shown), and run the

 

 

 

 

treadmill for a few minutes to check for a correct

 

 

 

 

speed reading.

 

 

 

 

PROBLEM: The incline of the treadmill does not change correctly

 

 

 

 

SOLUTION: a. Recalibrate the incline system (see step 3 on page 22).

 

 

 

 

PROBLEM: The iFit Live mode does not function correctly

 

 

 

 

SOLUTION: a. If the iFit Live mode is not functioning correctly, make sure that the treadmill has the most current

firmware available (see step 8 on page 23).

 

 

 

 

PROBLEM: The walking belt slows when walked on

 

 

 

 

SOLUTION: a. Use only a single-outlet surge suppressor that meets all of the specifications described on page 11.

b. If the walking belt is overtightened, treadmill perfor-

b

 

 

 

mance may decrease and the walking belt may be-

3–4 in.

 

 

come damaged. Remove the key and UNPLUG THE

 

 

 

POWER CORD. Using the hex key, turn both idler

 

 

 

 

roller bolts counterclockwise, 1/4 of a turn. When the

 

 

 

 

walking belt is properly tightened, you should be able

 

 

 

 

to lift each edge of the walking belt 3 to 4 in. (8 to 10

 

 

 

 

cm) off the walking platform. Be careful to keep the

 

 

 

 

walking belt centered. Then, plug in the power cord,

 

 

 

 

insert the key, and run the treadmill for a few min-

Idler Roller Bolts

 

 

utes. Repeat until the walking belt is properly tight-

 

 

ened.

 

 

 

 

c. If the walking belt still slows when walked on, please see the front cover of this manual.

26

Image 26
Contents Mon.-Fri a.m.-6 p.m. MT Sat a.m.-4 p.m. MT QUESTIONS?Model No. PFTL15010.0 Serial No On the WEBTable of Contents Important Precautions Page Before YOU Begin Assembly WrenchTo pinch the Upright Wire Bolts yet Attach the Left Upright 91 in the same wayWire Tie Console Assembly 110 Assembly Make sure to keep the latch cap inside PRE-LUBRICATED Walking Belt Operation and AdjustmentHOW to Plug in the Power Cord Console Diagram Features of the ConsoleHOW to Turn on the Power HOW to USE the Manual ModePage This, the treadmillʼs electrical components may Power cord. Important If you do not doMeasure your heart rate if desired Wear prematurelyHOW to USE a SET-A-GOAL Workout Start the workoutStart the workout Monitor your progress Select the iFit Live mode HOW to USE the Ifit Live ModeConnect your treadmill to your own wireless network Ifit Live FCC InformationSelect the settings mode HOW to USE the Stereo Sound SystemHOW to USE the Settings Mode Select the wireless network modeLog in to your iFit Live account Change the international settingsExit the settings mode Perform a network test HOW to USE the Maintenance ModeCalibrate the screen Exit the maintenance mode View technical informationHOW to Move the Treadmill HOW to Fold and Move the TreadmillHOW to Fold the Treadmill HOW to Lower the Treadmill for USECompatible with GFCI-equipped outlets TroubleshootingProblem The power turns off during use Top Problem The iFit Live mode does not function correctlyProblem The walking belt slows when walked on Problem Solution Workout Guidelines Exercise GuidelinesExercise Intensity Exercise FrequencyPart List Qty DescriptionDescription Key No. Qty Exploded Drawing a Exploded Drawing B Exploded Drawing C Exploded Drawing D Exploded Drawing E Icon Health & Fitness, Inc., 1500 S W., Logan, UT Ordering Replacement PartsLimited Warranty