ProForm 2 HOW to USE the Maintenance Mode, Calibrate the screen, Perform a network test

Page 22

HOW TO USE THE MAINTENANCE MODE

The console features a maintenance mode that allows you to calibrate the incline and speed of the treadmill, restore factory defaults, calibrate the screen, perform a network test, update the console firmware, and view technical information.

1.Select the settings mode. See step 1 on page 20.

2.Select the maintenance mode. Press the Maintenance button in the lower right corner of the screen to

enter the maintenance mode.

The maintenance mode main screen will show in- formation about the model and version of the treadmill.

If the console is connected to the controller of the treadmill, the controller dot will be green. If it is not, the dot will be red. If it is attempting to connect, the dot will be yellow.

If the treadmill is connected to your wireless net- work and is connected to iFit.com, the network dot will be green. If your treadmill is connected to your wireless network, but not to iFit.com, the dot will be yellow. If your treadmill is not connected, the dot will be red.

3.Calibrate the incline system of the treadmill. Press the Calibrate Incline button. Then, press the Begin button to calibrate the incline or the Cancel button to return to the maintenance mode. If you press the Begin button, the treadmill will automati- cally rise to the maximum incline level, lower to the minimum incline level and then return to the start- ing position. This will recalibrate the incline system. When the incline system is calibrated, press the Back button.

IMPORTANT: Keep pets, feet, and other objects away from the treadmill while the incline is cali- brating. In an emergency, pull the key from the console to stop the incline calibration.

4.Restore factory defaults.

If necessary, press the Restore Defaults button to reset the firmware to the original factory firmware. This will erase all firmware updates that you have downloaded. Press the Begin button to restore the default firmware or the Cancel button to return to the maintenance mode.

When the restoration is complete, the words PLEASE CYCLE POWER will appear in the grey box. Press the power switch on the treadmill frame into the off position. Wait for several seconds, and then press the power switch into the reset position. It may take a minute for the console to be ready for use.

5.Calibrate the screen.

If the screen is not properly calibrated, it will be dif- ficult to press the buttons on the screen. To cali- brate the screen, press the Calibrate Screen button and then press the Begin button. Press the Cancel button to return to the maintenance mode.

Using a pencil eraser or other small object, press the center of the small target on the screen. Then, press the next two targets. After several seconds, the console will return to the start menu.

6.Perform a network test.

If desired, press the Network Test button to check the connection status of the treadmill. The previous router status shows whether the treadmill has ever connected to a wireless router. The current router status shows whether the treadmill is currently con- nected to a wireless router. The network access status shows whether the treadmill can connect to your wireless network. The DNS status shows whether the treadmill can communicate with the DNS server. The iFit.com status shows whether the treadmill can communicate with iFit.com.

22

Image 22
Contents Mon.-Fri a.m.-6 p.m. MT Sat a.m.-4 p.m. MT QUESTIONS?Model No. PFTL15010.0 Serial No On the WEBTable of Contents Important Precautions Page Before YOU Begin Assembly WrenchTo pinch the Upright Wire Bolts yet Attach the Left Upright 91 in the same wayWire Tie Console Assembly 110 Assembly Make sure to keep the latch cap inside HOW to Plug in the Power Cord Operation and AdjustmentPRE-LUBRICATED Walking Belt Console Diagram Features of the ConsoleHOW to Turn on the Power HOW to USE the Manual ModePage This, the treadmillʼs electrical components may Power cord. Important If you do not doMeasure your heart rate if desired Wear prematurelyHOW to USE a SET-A-GOAL Workout Start the workoutStart the workout Monitor your progress Select the iFit Live mode HOW to USE the Ifit Live ModeConnect your treadmill to your own wireless network Ifit Live FCC InformationSelect the settings mode HOW to USE the Stereo Sound SystemHOW to USE the Settings Mode Select the wireless network modeExit the settings mode Change the international settingsLog in to your iFit Live account Calibrate the screen HOW to USE the Maintenance ModePerform a network test Exit the maintenance mode View technical informationHOW to Move the Treadmill HOW to Fold and Move the TreadmillHOW to Fold the Treadmill HOW to Lower the Treadmill for USEProblem The power turns off during use TroubleshootingCompatible with GFCI-equipped outlets Problem The walking belt slows when walked on Problem The iFit Live mode does not function correctlyTop Problem Solution Workout Guidelines Exercise GuidelinesExercise Intensity Exercise FrequencyPart List Qty DescriptionDescription Key No. Qty Exploded Drawing a Exploded Drawing B Exploded Drawing C Exploded Drawing D Exploded Drawing E Limited Warranty Ordering Replacement PartsIcon Health & Fitness, Inc., 1500 S W., Logan, UT