ProForm 1080 warranty Top, Problem The walking belt slows when walked on

Page 30

Locate the Reed Switch (52) and the Magnet (50)

 

 

on the left side of the Pulley (49). Turn the Pulley

 

 

until the Magnet is aligned with the Reed Switch.

 

 

Make sure that the gap between the Magnet and

52

49

the Reed Switch is about 1/8 in. (3 mm). If nec-

essary, loosen the #8 x 3/4" Tek Screw (14), move

14

50

the Reed Switch slightly, and then retighten the

1/8 in.

 

Screw. Reattach the Motor Hood (not shown) and

 

 

run the treadmill for a few minutes to check for a

Top

 

correct speed reading.

 

 

View

 

PROBLEM: The incline of the treadmill does not change correctly

SOLUTION: a. Recalibrate the incline system (see step 3 on page 26).

PROBLEM: The walking belt slows when walked on

SOLUTION: a. Use only a single-outlet surge suppressor that meets all of the specifications described on page 15.

b. If the walking belt is overtightened, treadmill perfor-

b

 

mance may decrease and the walking belt may be-

2–3 in.

come damaged. Remove the key and UNPLUG

 

THE POWER CORD. Using the hex key, turn both

 

 

idler roller bolts counterclockwise, 1/4 of a turn.

 

 

When the walking belt is properly tightened, you

 

 

should be able to lift each edge of the walking belt

 

 

2 to 3 in. (5 to 7 cm) off the walking platform. Be

 

 

careful to keep the walking belt centered. Then,

 

 

plug in the power cord, insert the key, and run the

Idler Roller Bolts

treadmill for a few minutes. Repeat until the walking

belt is properly tightened.

 

 

c. If the walking belt still slows when walked on, see the front cover of this manual.

PROBLEM: The walking belt is off-center or slips when walked on

 

 

SOLUTION: a. If the walking belt is off-center, first remove the

a

 

key and UNPLUG THE POWER CORD. If the

 

walking belt has shifted to the left, use the hex

 

 

key to turn the left idler roller bolt clockwise 1/2 of a

 

 

turn; if the walking belt has shifted to the right,

 

 

turn the left idler roller bolt counterclockwise 1/2 of

 

 

a turn. Be careful not to overtighten the walking

 

 

belt. Then, plug in the power cord, insert the key,

 

 

and run the treadmill for a few minutes. Repeat

 

 

until the walking belt is centered.

 

 

30

Page 29 Page 31
Image 30
Page 29 Page 31
Contents Mon.-Fri a.m.-6 p.m. MT Sat a.m.-4 p.m. MT QUESTIONS?Model No. PFTL11010.0 Serial No On the WEBTable of Contents Important Precautions Save These InstructionsBefore YOU Begin Assembly Wrench ScissorsMake sure that the power cord is unplugged See the inset drawing. Tie the wire tieAttach the Right Upright not shown Be careful not to pinch the UprightTighten the Bolts yet. Note Use the short hex Base Covers into place yetAttach the Right Handrail 87 in the same way Important To avoid damaging Shown. Start all four Screws, and then tighten Each of themAgain. if YOU do not Connect the CON All four Bolts, and then tighten each ThemPage Cardboard Page Operation and Adjustment HOW to Plug in the Power CordPRE-LUBRICATED Walking Belt Diagram Features of the ConsoleConsole Insert the key into the console HOW to Turn on the PowerHOW to USE the Manual Mode Select the start menuPage Measure your heart rate if desired. Before using HOW to USE a SET-A-GOAL Workout Start the workoutStart the workout See on Select the iFit Live mode HOW to USE the Ifit Live ModeConnect your treadmill to your own wireless network Ifit Live FCC InformationSelect the settings mode HOW to USE the Stereo Sound SystemHOW to USE the Settings Mode Select the wireless network modeChange the international settings Exit the settings modeLog in to your iFit Live account HOW to USE the Maintenance Mode Calibrate the screenExit the maintenance mode View technical informationHOW to Move the Treadmill HOW to Fold and Move the TreadmillHOW to Fold the Treadmill HOW to Lower the Treadmill for USETroubleshooting Problem The power turns off during useOutlets Problem The walking belt slows when walked on TopTurn if the walking belt has shifted to the right Problem The iFit Live mode does not function correctly Problem The buttons on the screen do not work correctlyWorkout Guidelines Exercise GuidelinesExercise Intensity Exercise FrequencySuggested Stretches Part List Key No. Qty DescriptionQty Exploded Drawing a Exploded Drawing B Exploded Drawing C Exploded Drawing D Ordering Replacement Parts Limited WarrantyIcon Health & Fitness, Inc., 1500 S W., Logan, UT
Top Page Image Contents