ProForm 1080 warranty HOW to USE the Maintenance Mode, Calibrate the screen

Page 26

HOW TO USE THE MAINTENANCE MODE

The console features a maintenance mode that allows you to calibrate the incline and speed of the treadmill, restore factory defaults, calibrate the screen, perform a network test, update the console firmware, and view technical information.

1.Select the settings mode. See step 1 on page 24.

2.Select the maintenance mode. Press the Maintenance button in the lower right corner of the screen to

enter the maintenance mode.

The maintenance mode main screen will show in- formation about the model and version of the treadmill.

If the treadmill is connected to your wireless net- work and is connected to iFit.com, the network dot will be green. If your treadmill is connected to your wireless network, but not to iFit.com, the dot will be yellow. If your treadmill is not connected, the dot will be red.

If the console is connected to the controller of the treadmill, the controller dot will be green. If it is not, the dot will be red. If it is attempting to connect, the dot will be yellow.

3.Calibrate the incline system of the treadmill. Press the Calibrate Incline button. Then, press the Begin button to calibrate the incline or the Cancel button to return to the maintenance mode. If you

press the Begin button, the treadmill will automati- cally rise to the maximum incline level, lower to the minimum incline level and then return to the start- ing position. This will recalibrate the incline system. When the incline system is calibrated, press the Finish button.

IMPORTANT: Keep pets, feet, and other objects away from the treadmill while the incline is cali- brating. In an emergency, pull the key from the console to stop the incline calibration.

4.Restore factory defaults.

If necessary, press the Restore Defaults button to reset the firmware to the original factory firmware. This will erase all firmware updates that you have downloaded. Press the Begin button to restore the default firmware or the Cancel button to return to the maintenance mode.

When the restoration is complete, the words PLEASE CYCLE POWER will appear in the grey box. Press the power switch on the treadmill frame into the off position (see page 5). Wait for several seconds, and then press the power switch into the reset position. It may take a minute for the console to be ready for use.

5.Calibrate the screen.

If the screen is not properly calibrated, it will be dif- ficult to press the buttons on the screen. To cali- brate the screen, press the Calibrate Screen button and then press the Begin button. Press the Cancel button to return to the maintenance mode.

Using a pencil eraser or other small object, press the center of the small target on the screen. Then, press the next two targets. After several seconds, the console will exit the maintenance mode.

26

Page 25 Page 27
Image 26
Page 25 Page 27
Contents Mon.-Fri a.m.-6 p.m. MT Sat a.m.-4 p.m. MT QUESTIONS?Model No. PFTL11010.0 Serial No On the WEBTable of Contents Important Precautions Save These InstructionsBefore YOU Begin Assembly Wrench ScissorsMake sure that the power cord is unplugged See the inset drawing. Tie the wire tieAttach the Right Upright not shown Be careful not to pinch the UprightTighten the Bolts yet. Note Use the short hex Base Covers into place yetAttach the Right Handrail 87 in the same way Again. if YOU do not Connect the CON Important To avoid damagingShown. Start all four Screws, and then tighten Each of them All four Bolts, and then tighten each ThemPage Cardboard Page PRE-LUBRICATED Walking Belt Operation and AdjustmentHOW to Plug in the Power Cord Console DiagramFeatures of the Console Insert the key into the console HOW to Turn on the PowerHOW to USE the Manual Mode Select the start menuPage Measure your heart rate if desired. Before using HOW to USE a SET-A-GOAL Workout Start the workoutStart the workout See on Select the iFit Live mode HOW to USE the Ifit Live ModeConnect your treadmill to your own wireless network Ifit Live FCC InformationSelect the settings mode HOW to USE the Stereo Sound SystemHOW to USE the Settings Mode Select the wireless network modeLog in to your iFit Live account Change the international settingsExit the settings mode HOW to USE the Maintenance Mode Calibrate the screenExit the maintenance mode View technical informationHOW to Move the Treadmill HOW to Fold and Move the TreadmillHOW to Fold the Treadmill HOW to Lower the Treadmill for USEOutlets TroubleshootingProblem The power turns off during use Turn if the walking belt has shifted to the right Problem The walking belt slows when walked onTop Problem The iFit Live mode does not function correctly Problem The buttons on the screen do not work correctlyWorkout Guidelines Exercise GuidelinesExercise Intensity Exercise FrequencySuggested Stretches Part List Key No. Qty DescriptionQty Exploded Drawing a Exploded Drawing B Exploded Drawing C Exploded Drawing D Icon Health & Fitness, Inc., 1500 S W., Logan, UT Ordering Replacement PartsLimited Warranty
Top Page Image Contents