ProForm PFSY74490 user manual Open the parts bag labeled Seat Assembly

Page 19

Seat Assembly

53.Open the parts bag labeled “SEAT ASSEMBLY.”

Press a 1” x 2” Inner Cap (83) into each end of a Backrest Adjustment Frame (70). Press a 1 1/4” Square Inner Cap (35) into the indicated tube on the Backrest Adjustment Frame.

Identify the Butterfly Backrest (12); it has only two holes in the back. Attach the Butterfly Backrest to the Backrest Adjustment Frame (70) with two 1/4” x 1 1/2” Bolts (82) and two 1/4” Flat Washers (71).

Pull the indicated Adjustment Knob (78) and slide the tube on the Backrest Adjustment Frame (70) into the Butterfly Upright (1). Release the Adjustment Knob and snap it into one of the holes in the Backrest Adjustment Frame. Secure it by turning the Knob clockwise.

54.Press a 1” x 2” Inner Cap (83) into each end of the Seat Adjustment Frame (90). Press a 1 1/4” Square Inner Cap (35) into the tube on the Seat Adjustment Frame.

Insert a 1/4” x 1 1/2” Carriage Bolt (101) into the cen- ter hole in a Seat Plate (65). Attach the Seat Plate to a Seat (13) with two 1/4” x 3/4” Bolts (49). Insert the 1/4” x 1 1/2” Carriage Bolt into the indicated hole in the Seat Adjustment Frame (90) and secure it with a 1/4” Flat Washer (71) and a 1/4” Nylon Locknut (68).

Secure the other end of the Seat (13) with a 1/4” x 1 1/2” Bolt (82) and a 1/4” Flat Washer (71).

Pull the indicated Adjustment Knob (78) and slide the tube on the Seat Adjustment Frame (90) into the slot in the Butterfly Seat Frame (14). Snap the Knob into a hole in the Frame and secure it by turning the Adjust-ment Knob clockwise.

55.Note: When using the Curl Pad (91), you must remove the 2” Square Inner Cap (28) that is in the Butterfly Front Leg (3). Replace the Inner Cap when you are not using the Curl Pad.

Attach the Curl Pad (91) to the Curl Post (107) with two 1/4” x 3/4” Bolts (49).

Insert the Curl Post (107) into the top of the Butterfly Front Leg (3).

53

 

 

 

 

83

 

 

70

71

78

 

12

35

 

 

 

 

 

 

82

1

 

 

 

83

71

 

 

 

 

 

54

 

 

 

13

101

 

 

 

 

 

65

 

 

 

49

 

83

 

 

 

 

90

 

 

 

83

 

71

 

 

 

 

71

68

78

 

 

 

 

82

 

 

 

35

 

 

 

 

 

14

 

55

 

 

 

 

49

 

 

91

28

 

 

107

 

 

 

 

 

 

3

 

 

19

Image 19
Contents Model No. PFSY74490 Serial No QUESTIONS?Important Precautions Table of ContentsBefore You Begin Frame Assembly Cable Assembly AssemblyArm Assembly Seat Assembly Bolt will be tipped at an angle Frame AssemblyGroove Pin Grooves Tighten all of the Nylon Locknuts 64 used in steps 5 Do not overtighten the Nylon Locknuts Tighten all of the Nylon Locknuts 64 used in this step Nylon Locknuts yetNylon Jam Nut the Press Front Leg must pivot freely Open the parts bag labeled ARM Assembly Arm AssemblyLarge Cable Trap is oriented as shown Cable AssemblyPage Make sure the Cable Trap is oriented as shown Trap is oriented as shown LockNut the Cable must pivot freely on the Bolt Page Cable Trap is oriented as shown Make sure that the Cable Trap is oriented as shown Open the parts bag labeled Seat Assembly Seat AssemblyPage 109 Cable Diagrams High Cable Changing the Weight Setting AdjustmentAdjusting the Press Plate Trouble-shooting and MaintenanceTightening the Cables Page TOP Weight Resistance ChartPart Identification Chart-Model No. PFSY74490 R0401A Page Page Qty Description Part List-Model No. PFSY74490Exploded Limited Warranty Ordering Replacement PartsIcon Health & FITNESS, INC., 1500 S W., LOGAN, UT