JVC RX-884PBK manual Video component connections, Video components

Page 13

Video component connections

Use the cables with RCA pin plugs (not supplied).

Connect the white plug to the audio left jack, the red plug to the audio right jack, and the yellow plug to the video jack.

If your video components have S-video (Y/C-separation) terminals, connect them using S-video cables (not supplied). Connecting these video components through the S-video input/output terminals will give you better picture playback (or recording) quality.

IMPORTANT:

This receiver is equipped with both the composite video and S-video input/output terminals for connecting video components.

You do not have to connect both the composite video and S-video terminals. However, remember that the video signals from the composite video input terminals are output only through the composite video output terminals, while the ones from the S-video input terminals are output only through the S-video output terminals.

Therefore, if a recording video component and a playing video component are connected to the receiver through the different video terminals, you cannot record the picture from the playing component on the recording component. In addition, if the TV and a playing video component are connected to the receiver through the different video terminals, you cannot view the playback picture from the playing component on the TV.

To view and record the playback picture from the video component connected to the VCR 2 jacks, you must connect the TV and the recording video component through the composite video terminals.

Connecting the TV and/or DBS tuner

You can connect either the TV or DBS tuner to the TV SOUND/DBS jacks.

English

Note:

When connecting an audio/ video component (ex.: Video CD player) with “karaoke” — singing along — function, use the audio signal attenuating cord supplied with this receiver. If not, sound may be distorted.

Notes:

AUDIO

RIGHT

LEFT

 

To audio output

 

Connect the TV to the

 

MONITOR OUT jack to

 

view the playback picture

 

from the other connected

TV

video components.

 

 

To composite video input

 

SUBWOOFER

 

OUT

 

To S-video input

VIDEO

VIDEO S-VIDEO

DVD

TV SOUND

/DBS

OUT

(REC)

VCR 1

IN

(PLAY)

OUT

(REC)

VCR 2

IN

(PLAY)

MONITOR

OUT

•

Use the video components of

 

the PAL color system.

•

When connecting the TV to

 

the TV SOUND/DBS jacks,

 

DO NOT connect the TV’s

 

video output to these video

 

input terminals.

•

When connecting the DBS

 

tuner to the TV SOUND/DBS

 

jacks, change the source

 

name, which will be shown on

 

the display when selected as

 

the source, to “DBS.” See

 

page 18 for details.

•

To enjoy Dolby Digital with the

 

DBS tuner as the source,

 

connect the DBS tuner using

 

the method described in

 

“Digital connections” on page

DBS tuner

TV SOUND

/DBS

DBS

To audio/video output

12.

10

Page 12 Page 14
Image 13
Page 12 Page 14
Contents RX-884PBK Precaución English Español Português Table of Contents Using the DSP Modes Parts Identification Remote ControlFront Panel Getting Started How to set the voltage selectorGeneral LocationsGetting Started Connecting the FM and AM AntennasFM Antenna Connections AM Antenna ConnectionsConnecting the Speakers Connecting the front speakersConnecting the subwoofer speaker Connecting the rear and center speakersCase 2 When you connect two sets of front speakers Case 1 When you connect only one set of front speakersAbout the speaker impedance Use front speakers with 4 16 ohm impedanceAnalog connections Connecting Audio/Video ComponentsAudio Components Video Components Audio component connectionsVideo components Video component connectionsConnecting DVD player Digital 1 coaxial For Digital connectionsTo shut off the power completely Connecting the Power CordPress Power to set it in the Ñoff position Putting Batteries in the Remote ControlTurning the Power On and Off Standby From the remote controlBasic Operations On the front panelBasic Operations Adjusting the VolumePress one of the source selecting buttons directly Selecting different sources for picture and soundListening only with headphones From the remote control onlyOn the front panel only Adjusting the Subwoofer Output Level Attenuating the Input SignalDisplay changes to show the current setting Keys are activated for sound adjustmentsSelecting the Input Mode Basic SettingsSelecting the DBS tuner as the source Changing the Source NameAdjusting the Front Speaker Output Balance Basic SettingsSetting the Subwoofer Information Listening at Low Volume LoudnessSetting the Speakers for the DSP Modes Digital Input Digital in Terminal SettingFront, Center, and Rear Speaker Setting SPK Rear Speaker appears on the displayRear Delay Time Setting Center Delay Time SettingCrossover Frequency Setting Dynamic Range Compression Setting Low Frequency Effect Attenuator SettingTo recall the sound settings To store the sound settingsTo cancel the One Touch Operation function One Touch OperationTuning in Stations Manually Setting the AM Tuner Interval SpacingReceiving Radio Broadcasts To select the 10 kHz intervalTo store the preset stations Using Preset TuningTo erase a stored preset station To tune in a preset stationPress FM Mode on the front panel or FM Mode Selecting the FM Reception ModeMute on the remote control Press Tuner PRESET, while a character you want is Assigning Names to Preset StationsFlashing Character is flashing after you have assigned a nameSelecting Your Favorite SEA Mode Using the SEA ModesTo cancel the SEA mode Creating Your Own SEA Mode Using the SEA ModesTo recall your own SEA adjustment To erase a stored adjustmentOn the 3D-PHONIC mode Using the DSP ModesOn the DAP mode On Surround modeUsing the 3D-PHONIC Modes Using the DSP ModesPress DSP Mode Turn Multi JOG until the mode 3D Action or 3DAs you turn it, the effect level changes as follows To cancel the 3D-PHONIC modeAction or 3D DIGITAL, 3D DRAMA, or 3D Theater Press Surround Mode repeatedly until the mode 3DYou want appears on the display Press Effect to select the effect levelUsing the DAP Modes Press Surround Mode repeatedly until the mode you To cancel the DAP modeAdjust the speaker output levels as follows Want appears on the displayPress Surround Mode repeatedly until PRO Logic Using the Dolby Digital and Dolby Pro Logic ModesOr Dolby Digital appears on the display Press Test to start checking the speaker output balance To cancel the Surround modePress Test again to stop the test tone Press Cntr Tone to select the center tone level you wantLights up Press Dolby Surround so that the lamp on the buttonTurn Multi JOG to select the center tone level you want Press Dolby Surround again so that Surround OFF appearsUsing the Theater Surround Mode To cancel the Theater Surround mode Center tone adjustment affects the mid-frequencyDSP and Theater indicators also light up on the display SOFT2 SOFT1 Flat SHARP1 When you select OSD, see Using the On-Screen MenusSelecting the Source to Play Also see Selecting the Different Sources for Picture and SoundListening at Low Volume Loudness Also see Adjusting the Front Speaker Output Balance Also seeAttenuating the Input Signal Also see Sound Control menu appears on the TVAdjusting the Subwoofer Output Level Also see Using the On-Screen MenusFor 3D-PHONIC modes For DAP modes Live CLUB, Dance CLUB, HALL, PavilionFor Dolby Surround Pro Logic Selecting Your Favorite SEA Mode Also seeFor Dolby Digital For Theater Surround and Digital Theater SurroundBasic Settings Creating Your Own SEA Mode Also seePress SET to store the setting into the SEA Usermode Operating the Tuner Storing the Preset Stations Also seeCharacter entry screen appears Assigning Names to the Preset Stations Also seeTuner Control menu appears again Remote Control through the Remote Sensor on the Receiver Compu Link Remote Control SystemAutomatic Source Selection Synchronized RecordingDisplaying the Disc Information on the TV screen Text Compu Link Remote Control SystemDisc Search Only for CD Player Additional FunctionsShowing the Disc Information on the TV Screen OperationsSearching a Disc Only for the CD player Text Compu Link Remote Control SystemSearch a disc by its performer Search a disc by its disc titleSearch a disc by its genre Going back to the Disc Title Search screen Press ExitPress on Screen Control %/ Þ to move to GENRE, then press Genre Search screen appearsUser File screen appears on the TV Using your own User FilesGoing back to the User File screen Press Exit For the CD Player with the disc memory function Entering the Disc InformationTitle Input Performer screen appears on the TV To move to Shift , then press SETEnter the disc title, referring to steps 3 and 4 on For the MD recorderEnter the song title, referring to steps 3 and 4 on Operating JVC’s Audio/Video Components CD player-changer Operating JVC’s Audio/Video ComponentsTurntable Cassette deckREC VCR1 the VCR connected to the VCR1 jacksDVD player Sets the input mode either TV or Adjusts the volumeTurns on or off the TV Try to operate your TV by pressing TV/CATV/DBS Operating Other Manufactures’ Components10, 0, 100++10 Operating Other Manufactures’ ComponentsPauses Starts playbackTry to operate your VCR by pressing VCR1 Manufacturers’ codes for TV Problem Possible Cause Solution TroubleshootingAmplifier SpecificationsVideo Important for mains AC line

RX-884PBK specifications

The JVC RX-884PBK is a powerful and versatile audio receiver that has garnered attention for its impressive features tailored to both casual listeners and dedicated audiophiles. Designed with a sleek and modern aesthetic, this receiver fits seamlessly into any home entertainment setup, delivering high-quality sound and an array of functionalities.

One of the standout features of the JVC RX-884PBK is its multi-channel audio support. This receiver is capable of delivering immersive surround sound, making it an excellent choice for home theater enthusiasts. With support for formats such as Dolby Digital and DTS, users can experience cinema-like audio directly in their living rooms, enhancing movies, music, and gaming experiences.

Power output is another highlight of the RX-884PBK, boasting significant wattage per channel that ensures clear and powerful audio across various speaker configurations. Whether you have a compact stereo setup or a full-fledged surround sound system, the receiver has the capacity to drive speakers effectively, providing dynamic range and depth in audio playback.

Connectivity is a crucial aspect of modern receivers, and the RX-884PBK does not disappoint. It offers multiple inputs, including analog, optical, and coaxial connections, allowing users to connect a variety of devices such as Blu-ray players, gaming consoles, and streaming devices. The built-in phono input also caters to vinyl enthusiasts, enabling direct connection to turntables for an authentic listening experience.

In terms of user interface, the JVC RX-884PBK features an intuitive control system that makes navigating through settings and configurations easy. The remote control adds an extra layer of convenience, allowing users to adjust settings from across the room without the need to get up.

Moreover, the receiver incorporates advanced technologies aimed at enhancing sound quality. With features such as digital signal processing, it can optimize audio playback for different environments. The equalizer settings provide users with the flexibility to customize sound according to personal preferences or specific genres.

In summary, the JVC RX-884PBK is a feature-rich audio receiver that caters to a wide range of listening preferences. Its powerful performance, extensive connectivity options, and user-friendly interface make it an ideal choice for anyone looking to elevate their home audio experience. Whether for movies, music, or gaming, this receiver is designed to deliver exceptional sound quality and enjoyment.
Top Page Image Contents