JVC RX-884PBK manual On the front panel, DSP and Theater indicators also light up on the display

Page 44

Using the DSP Modes

English

On the front panel:

You can also use the buttons on the front panel to adjust the Theater Surround mode. However, no test tone is available when using the buttons on the front panel. So, make adjustments while listening to the sound of the source played back.

1. Select and play the source encoded with Dolby Digital (bearing the mark

) or with Dolby Surround (bearing the mark

 

 

DOLBY SURROUND

).

D I G I T A L

•When you play back the source encoded with Dolby Digital and select the digital input for that source, the Ù DIGITAL indicator lights up on the display.

Notes:

•

To enjoy the software encoded

 

with Dolby Digital, you must

 

connect the source

 

component using the digital

 

terminal on the rear of this

 

receiver.

•

The Surround mode is not

 

used with the other DSP

 

modes such as the DAP mode

2.Press DSP MODE.

The current DSP mode appears on the display.

3.Turn MULTI JOG until “THEATER” or “DIG- THEATER” appears on the display, while the indication of the previous step is still on the display.

The DSP and THEATER indicators also light up on the display.

DSP MODE

MULTI JOG

and 3D-PHONIC mode. When

the Surround mode is turned

on, the other DSP mode, if

used, will be turned off.

Notes on the indications:

As you turn it, the DSP modes change as follows:

When the digital input is selected to play the source encoded with Dolby Digital:

DIG-THEATERHEADPHONE

DSP OFF 3D DIGITAL

For other sources:

THEATER LIVE CLUB DANCE CLUB HALL

DSP OFF

 

PAVILION

 

 

3D THEATER

 

3D DRAMA

 

3D ACTION

 

HEADPHONE

 

 

 

 

 

 

 

 

 

If you need to make any adjustment, go to the following steps.

•The PRO LOGIC indicator lights up when the Dolby Pro Logic decoder built in this receiver is activated.

•The Dolby Pro Logic decoder is used not only for the analog sources but also for the sources encoded with Dolby Digital in the following cases:

–When only front channel signals are encoded.

–When front channel and monaural rear channel

signals are encoded. While the Dolby Pro Logic is activated for this type of Dolby Digital source, the Ù DIGITAL indicator goes off.

4.Adjust the speaker output levels as follows.

1)Press BALANCE/SURROUND ADJUST repeatedly until one of the indications appears on the display. “CENTER LEVEL”: To adjust the center speaker level. “REAR L LEVEL”: To adjust the left speaker level. “REAR R LEVEL”: To adjust the right speaker level.

2)Turn MULTI JOG to adjust the selected speaker output level (from –10 dB to +10 dB), while the indication of the previous step is still on the display.

3)Repeat 1) and 2) to adjust the other speaker output levels.

BALANCE/SURROUND

ADJUST

MULTI JOG

Notes:

•You cannot adjust the center speaker level when “CENTER SPK” is set to “NONE” (see page 20).

•You cannot adjust the rear speaker levels when “REAR SPK” is set to “NONE” (see page 20).

41

Page 43 Page 45
Image 44
Page 43 Page 45
Contents RX-884PBK Precaución English Español Português Table of Contents Using the DSP Modes Front Panel Remote ControlParts Identification How to set the voltage selector Getting StartedGeneral LocationsConnecting the FM and AM Antennas Getting StartedFM Antenna Connections AM Antenna ConnectionsConnecting the front speakers Connecting the SpeakersConnecting the rear and center speakers Connecting the subwoofer speakerCase 1 When you connect only one set of front speakers Case 2 When you connect two sets of front speakersAbout the speaker impedance Use front speakers with 4 16 ohm impedanceConnecting Audio/Video Components Analog connectionsAudio Components Video Components Audio component connectionsVideo component connections Video componentsConnecting DVD player Digital connections Digital 1 coaxial ForConnecting the Power Cord To shut off the power completelyPress Power to set it in the Ñoff position Putting Batteries in the Remote ControlFrom the remote control Turning the Power On and Off StandbyBasic Operations On the front panelAdjusting the Volume Basic OperationsPress one of the source selecting buttons directly Selecting different sources for picture and soundOn the front panel only From the remote control onlyListening only with headphones Attenuating the Input Signal Adjusting the Subwoofer Output LevelDisplay changes to show the current setting Keys are activated for sound adjustmentsBasic Settings Selecting the Input ModeSelecting the DBS tuner as the source Changing the Source NameBasic Settings Adjusting the Front Speaker Output BalanceSetting the Subwoofer Information Listening at Low Volume LoudnessDigital Input Digital in Terminal Setting Setting the Speakers for the DSP ModesFront, Center, and Rear Speaker Setting SPK Rear Speaker appears on the displayCrossover Frequency Setting Center Delay Time SettingRear Delay Time Setting Low Frequency Effect Attenuator Setting Dynamic Range Compression SettingTo store the sound settings To recall the sound settingsTo cancel the One Touch Operation function One Touch OperationSetting the AM Tuner Interval Spacing Tuning in Stations ManuallyReceiving Radio Broadcasts To select the 10 kHz intervalUsing Preset Tuning To store the preset stationsTo erase a stored preset station To tune in a preset stationMute on the remote control Selecting the FM Reception ModePress FM Mode on the front panel or FM Mode Assigning Names to Preset Stations Press Tuner PRESET, while a character you want isFlashing Character is flashing after you have assigned a nameTo cancel the SEA mode Using the SEA ModesSelecting Your Favorite SEA Mode Using the SEA Modes Creating Your Own SEA ModeTo recall your own SEA adjustment To erase a stored adjustmentUsing the DSP Modes On the 3D-PHONIC modeOn the DAP mode On Surround modeUsing the DSP Modes Using the 3D-PHONIC ModesPress DSP Mode Turn Multi JOG until the mode 3D Action or 3DTo cancel the 3D-PHONIC mode As you turn it, the effect level changes as followsPress Surround Mode repeatedly until the mode 3D Action or 3D DIGITAL, 3D DRAMA, or 3D TheaterYou want appears on the display Press Effect to select the effect levelUsing the DAP Modes To cancel the DAP mode Press Surround Mode repeatedly until the mode youAdjust the speaker output levels as follows Want appears on the displayOr Dolby Digital appears on the display Using the Dolby Digital and Dolby Pro Logic ModesPress Surround Mode repeatedly until PRO Logic To cancel the Surround mode Press Test to start checking the speaker output balancePress Test again to stop the test tone Press Cntr Tone to select the center tone level you wantPress Dolby Surround so that the lamp on the button Lights upTurn Multi JOG to select the center tone level you want Press Dolby Surround again so that Surround OFF appearsUsing the Theater Surround Mode Center tone adjustment affects the mid-frequency To cancel the Theater Surround modeDSP and Theater indicators also light up on the display SOFT2 SOFT1 Flat SHARP1 Using the On-Screen Menus When you select OSD, seeSelecting the Source to Play Also see Selecting the Different Sources for Picture and SoundAdjusting the Front Speaker Output Balance Also see Listening at Low Volume Loudness Also seeAttenuating the Input Signal Also see Sound Control menu appears on the TVUsing the On-Screen Menus Adjusting the Subwoofer Output Level Also seeFor 3D-PHONIC modes For DAP modes Live CLUB, Dance CLUB, HALL, PavilionSelecting Your Favorite SEA Mode Also see For Dolby Surround Pro LogicFor Dolby Digital For Theater Surround and Digital Theater SurroundPress SET to store the setting into the SEA Usermode Creating Your Own SEA Mode Also seeBasic Settings Storing the Preset Stations Also see Operating the TunerTuner Control menu appears again Assigning Names to the Preset Stations Also seeCharacter entry screen appears Compu Link Remote Control System Remote Control through the Remote Sensor on the ReceiverAutomatic Source Selection Synchronized RecordingText Compu Link Remote Control System Displaying the Disc Information on the TV screenDisc Search Only for CD Player Additional FunctionsOperations Showing the Disc Information on the TV ScreenText Compu Link Remote Control System Searching a Disc Only for the CD playerSearch a disc by its performer Search a disc by its disc titleGoing back to the Disc Title Search screen Press Exit Search a disc by its genrePress on Screen Control %/ Þ to move to GENRE, then press Genre Search screen appearsGoing back to the User File screen Press Exit Using your own User FilesUser File screen appears on the TV Entering the Disc Information For the CD Player with the disc memory functionTitle Input Performer screen appears on the TV To move to Shift , then press SETEnter the song title, referring to steps 3 and 4 on For the MD recorderEnter the disc title, referring to steps 3 and 4 on Operating JVC’s Audio/Video Components Operating JVC’s Audio/Video Components CD player-changerTurntable Cassette deckDVD player VCR1 the VCR connected to the VCR1 jacksREC Turns on or off the TV Adjusts the volumeSets the input mode either TV or Operating Other Manufactures’ Components Try to operate your TV by pressing TV/CATV/DBSOperating Other Manufactures’ Components 10, 0, 100++10Try to operate your VCR by pressing VCR1 Starts playbackPauses Manufacturers’ codes for TV Troubleshooting Problem Possible Cause SolutionSpecifications AmplifierVideo Important for mains AC line

RX-884PBK specifications

The JVC RX-884PBK is a powerful and versatile audio receiver that has garnered attention for its impressive features tailored to both casual listeners and dedicated audiophiles. Designed with a sleek and modern aesthetic, this receiver fits seamlessly into any home entertainment setup, delivering high-quality sound and an array of functionalities.

One of the standout features of the JVC RX-884PBK is its multi-channel audio support. This receiver is capable of delivering immersive surround sound, making it an excellent choice for home theater enthusiasts. With support for formats such as Dolby Digital and DTS, users can experience cinema-like audio directly in their living rooms, enhancing movies, music, and gaming experiences.

Power output is another highlight of the RX-884PBK, boasting significant wattage per channel that ensures clear and powerful audio across various speaker configurations. Whether you have a compact stereo setup or a full-fledged surround sound system, the receiver has the capacity to drive speakers effectively, providing dynamic range and depth in audio playback.

Connectivity is a crucial aspect of modern receivers, and the RX-884PBK does not disappoint. It offers multiple inputs, including analog, optical, and coaxial connections, allowing users to connect a variety of devices such as Blu-ray players, gaming consoles, and streaming devices. The built-in phono input also caters to vinyl enthusiasts, enabling direct connection to turntables for an authentic listening experience.

In terms of user interface, the JVC RX-884PBK features an intuitive control system that makes navigating through settings and configurations easy. The remote control adds an extra layer of convenience, allowing users to adjust settings from across the room without the need to get up.

Moreover, the receiver incorporates advanced technologies aimed at enhancing sound quality. With features such as digital signal processing, it can optimize audio playback for different environments. The equalizer settings provide users with the flexibility to customize sound according to personal preferences or specific genres.

In summary, the JVC RX-884PBK is a feature-rich audio receiver that caters to a wide range of listening preferences. Its powerful performance, extensive connectivity options, and user-friendly interface make it an ideal choice for anyone looking to elevate their home audio experience. Whether for movies, music, or gaming, this receiver is designed to deliver exceptional sound quality and enjoyment.
Top Page Image Contents