JVC RX-884PBK manual Operating JVC’s Audio/Video Components

Operating JVC’s Audio/Video Components

You can operate JVC’s audio and video components with this receiver’s remote control, since control signals for JVC components are preset in the remote control.

English

IMPORTANT:

To operate JVC’s audio components using this remote control:

•You need to connect JVC audio components through the COMPU LINK-3 (SYNCHRO) jacks (see page 50) in addition to the connections using cables with RCA pin plugs (see page 9) or using digital cables (see page 12).

•Aim the remote control directly at the remote sensor on the receiver.

Notes:

• If you use the buttons on the

front panel or the menu

function to choose a source,

the remote control will not

operate that source. To

operate a source with the

Tuner

After pressing FM/AM (with the remote control mode selector set to “AUDIO/TV/VCR” ), you can perform the following operations:

FM/AM:Alternates between FM and AM.

1 – 10, +10: Selects a preset channel number directly. For channel number 5, press 5. For channel number 15, press +10, then 5. For channel number 20, press +10, then 10.

TUNING UP/TUNING DOWN:

Tunes into stations.

FM MODE/MUTE: Changes the FM reception mode.

Sound control section (Amplifier)

You can always perform the following operations (with the remote control mode selector set to “AUDIO/TV/VCR”) : SURROUND MODE: Changes the DSP modes.

After pressing SOUND CONTROL (with the remote control mode selector set to “AUDIO/TV/VCR”) , you can perform the following operations:

SEA MODE:	Changes the SEA modes.
SUBWOOFER +/–:Adjusts the subwoofer output level.
CNTR +/–:	Adjusts the center speaker output
	level.
REAR•L +/–:	Adjusts the left rear speaker output
	level.
REAR•R +/–:	Adjusts the right rear speaker output level.
EFFECT:	Selects the effect level.
TEST:	Turns on or off the test tone output.
CNTR TONE:	Selects the center tone.

CD player

RM-SR884XU REMOTE CONTROL

TV/CATV		VCR1		ANALOG			AUDIO
/DBS				/DIGITAL
DVD		VCR1		VCR2			VIDEO
CD TAPE/MD PHONO							FM/AM
TV/DBS CNTR TONE				2	CNTR MENU
SURROUND			1				3
		TEST ENTER REAR L
MODE			4	5			6
SOUND
		EFFECT			REAR R
CONTROL		7/P		8			9
CD
		SEA MODE		SUBWOOFER
DISC		10		0			+10
		RETURN FM MODE/MUTE					100+
AUDIO/TV
/VCR
			VOLUME
CATV
/DBS
			CHANNEL
MUTE
				TUNING UP
					FF / ¢
DOWN PLAY
TUNING/REW
4
						PAUSE
			STOP
REC
				TV VOLUME
TV/VIDEO
			CONTROL
		VCR1		TAPE
SET							EXIT
O							L
N	S				T		O
		C		N		R
			REEN CO

	remote control, the source
	must be selected using
	buttons on the remote control.
•	Check to see if its remote
	control mode selector is set to
	the correct position. To
	operate audio system, TVs,
	and VCRs, set it to “AUDIO/
	TV/VCR.”
•	Refer also to the manuals
	supplied with your
	components.

Note:

After adjusting sounds, press the corresponding source selecting button or CD DISC to operate your target source by using 10 keys; otherwise, 10 keys cannot be used for operating your target source.

After pressing CD (with the remote control mode selector set to “AUDIO/TV/VCR” ), you can perform the following operations on a CD player:

PLAY:	Starts playing.
4:	Returns to the beginning of the current (or previous) track.
¢:	Skips to the beginning of the next track.
STOP:	Stops playing.
PAUSE:	Pauses playing. To release it, press PLAY.

1 – 10, +10: Selects a track number directly.

For track number 5, press 5. For track number 15, press +10, then 5. For track number 20, press +10, then 10. For track number 30, press +10, +10, then 10.

58