JVC RX-884PBK manual Digital connections, Digital 1 coaxial For

Page 15

Digital connections

This receiver is equipped with three DIGITAL IN terminals — one digital coaxial terminal and two digital optical terminals.

To enjoy Dolby Digital, you have to connect the source components using the DIGITAL IN terminals.

You can connect any component to any one of the digital terminals using the digital coaxial cable (not supplied) or digital optical cable (not supplied).

English

DBS tuner

DBS

DVD player

DVD

When the component has a digital coaxial output terminal, connect it to the DIGITAL1 (DBS) terminal, using the digital coaxial cable (not supplied).

DIGITAL IN

PCM/DOLBY DIGITAL

Notes:

• When shipped from the

factory, the DIGITAL IN

terminals has been set for use

with the following

components.

– DIGITAL 1 (coaxial): For

CD player

MD recorder

When the component has a digital optical output terminal, connect it to the DIGITAL2 (DVD) or DIGITAL3 (CD) terminal, using the digital optical cable (not supplied).

Before connecting a digital optical cable, unplug the protective plug.

DIGITAL 1 (DBS)

DIGITAL 2 (DVD)

DIGITAL 3 (CD)

DBS tuner

– DIGITAL 2 (optical): For

DVD player

– DIGITAL 3 (optical): For CD

player

• When you want to operate the

CD player or MD recorder

using the COMPU LINK

remote control system,

connect the target component

also as described in “Analog

connections” (see page 9).

IMPORTANT:

•When connecting the DVD player or the DBS tuner using the digital terminal, you also need to connect it to the video jack (either composite video terminal or S-video terminal) on the rear. Without connecting it to the video jack, you can view no playback picture.

•After connecting the above components using the DIGITAL IN terminals, set the following correctly if necessary.

–Select the digital input mode correctly. For details, see “Selecting the Input Mode” on page 18.

–Set the digital input (DIGITAL IN) terminal setting correctly. For details, see “Digital Input (DIGITAL IN) Terminal Setting” on page 20.

12

Image 15

Contents RX-884PBK Precaución English Español Português Table of Contents Using the DSP Modes Remote Control Parts IdentificationFront Panel Locations How to set the voltage selectorGetting Started GeneralAM Antenna Connections Connecting the FM and AM AntennasGetting Started FM Antenna ConnectionsConnecting the Speakers Connecting the front speakersConnecting the subwoofer speaker Connecting the rear and center speakersUse front speakers with 4 16 ohm impedance Case 1 When you connect only one set of front speakersCase 2 When you connect two sets of front speakers About the speaker impedance Audio component connections Connecting Audio/Video Components Analog connections Audio Components Video ComponentsVideo components Video component connectionsConnecting DVD player Digital 1 coaxial For Digital connectionsPutting Batteries in the Remote Control Connecting the Power CordTo shut off the power completely Press Power to set it in the Ñoff positionOn the front panel From the remote controlTurning the Power On and Off Standby Basic OperationsSelecting different sources for picture and sound Adjusting the VolumeBasic Operations Press one of the source selecting buttons directlyFrom the remote control only Listening only with headphonesOn the front panel only Keys are activated for sound adjustments Attenuating the Input SignalAdjusting the Subwoofer Output Level Display changes to show the current settingChanging the Source Name Basic SettingsSelecting the Input Mode Selecting the DBS tuner as the sourceListening at Low Volume Loudness Basic SettingsAdjusting the Front Speaker Output Balance Setting the Subwoofer InformationSPK Rear Speaker appears on the display Digital Input Digital in Terminal SettingSetting the Speakers for the DSP Modes Front, Center, and Rear Speaker SettingCenter Delay Time Setting Rear Delay Time SettingCrossover Frequency Setting Dynamic Range Compression Setting Low Frequency Effect Attenuator SettingOne Touch Operation To store the sound settingsTo recall the sound settings To cancel the One Touch Operation functionTo select the 10 kHz interval Setting the AM Tuner Interval SpacingTuning in Stations Manually Receiving Radio BroadcastsTo tune in a preset station Using Preset TuningTo store the preset stations To erase a stored preset stationSelecting the FM Reception Mode Press FM Mode on the front panel or FM ModeMute on the remote control Character is flashing after you have assigned a name Assigning Names to Preset StationsPress Tuner PRESET, while a character you want is FlashingUsing the SEA Modes Selecting Your Favorite SEA ModeTo cancel the SEA mode To erase a stored adjustment Using the SEA ModesCreating Your Own SEA Mode To recall your own SEA adjustmentOn Surround mode Using the DSP ModesOn the 3D-PHONIC mode On the DAP modeTurn Multi JOG until the mode 3D Action or 3D Using the DSP ModesUsing the 3D-PHONIC Modes Press DSP ModeAs you turn it, the effect level changes as follows To cancel the 3D-PHONIC modePress Effect to select the effect level Press Surround Mode repeatedly until the mode 3DAction or 3D DIGITAL, 3D DRAMA, or 3D Theater You want appears on the displayUsing the DAP Modes Want appears on the display To cancel the DAP modePress Surround Mode repeatedly until the mode you Adjust the speaker output levels as followsUsing the Dolby Digital and Dolby Pro Logic Modes Press Surround Mode repeatedly until PRO LogicOr Dolby Digital appears on the display Press Cntr Tone to select the center tone level you want To cancel the Surround modePress Test to start checking the speaker output balance Press Test again to stop the test tonePress Dolby Surround again so that Surround OFF appears Press Dolby Surround so that the lamp on the buttonLights up Turn Multi JOG to select the center tone level you wantUsing the Theater Surround Mode To cancel the Theater Surround mode Center tone adjustment affects the mid-frequencyDSP and Theater indicators also light up on the display SOFT2 SOFT1 Flat SHARP1 Selecting the Different Sources for Picture and Sound Using the On-Screen MenusWhen you select OSD, see Selecting the Source to Play Also seeSound Control menu appears on the TV Adjusting the Front Speaker Output Balance Also seeListening at Low Volume Loudness Also see Attenuating the Input Signal Also seeFor DAP modes Live CLUB, Dance CLUB, HALL, Pavilion Using the On-Screen MenusAdjusting the Subwoofer Output Level Also see For 3D-PHONIC modesFor Theater Surround and Digital Theater Surround Selecting Your Favorite SEA Mode Also seeFor Dolby Surround Pro Logic For Dolby DigitalCreating Your Own SEA Mode Also see Basic SettingsPress SET to store the setting into the SEA Usermode Operating the Tuner Storing the Preset Stations Also seeAssigning Names to the Preset Stations Also see Character entry screen appearsTuner Control menu appears again Synchronized Recording Compu Link Remote Control SystemRemote Control through the Remote Sensor on the Receiver Automatic Source SelectionAdditional Functions Text Compu Link Remote Control SystemDisplaying the Disc Information on the TV screen Disc Search Only for CD PlayerShowing the Disc Information on the TV Screen OperationsSearch a disc by its disc title Text Compu Link Remote Control SystemSearching a Disc Only for the CD player Search a disc by its performerGenre Search screen appears Going back to the Disc Title Search screen Press ExitSearch a disc by its genre Press on Screen Control %/ Þ to move to GENRE, then pressUsing your own User Files User File screen appears on the TVGoing back to the User File screen Press Exit To move to Shift , then press SET Entering the Disc InformationFor the CD Player with the disc memory function Title Input Performer screen appears on the TVFor the MD recorder Enter the disc title, referring to steps 3 and 4 onEnter the song title, referring to steps 3 and 4 on Operating JVC’s Audio/Video Components Cassette deck Operating JVC’s Audio/Video ComponentsCD player-changer TurntableVCR1 the VCR connected to the VCR1 jacks RECDVD player Adjusts the volume Sets the input mode either TV orTurns on or off the TV Try to operate your TV by pressing TV/CATV/DBS Operating Other Manufactures’ Components10, 0, 100++10 Operating Other Manufactures’ ComponentsStarts playback PausesTry to operate your VCR by pressing VCR1 Manufacturers’ codes for TV Problem Possible Cause Solution TroubleshootingAmplifier SpecificationsVideo Important for mains AC line