JVC RX-884PBK manual Getting Started, General, Locations, Handling the receiver

Page 7

Getting Started

This section explains how to connect audio/video components and speakers to the receiver, and how to connect the power supply.

Before Installation

General

•Be sure your hands are dry.

•Turn the power off to all components.

•Read the manuals supplied with the components you are going to connect.

Locations

•Install the receiver in a location that is level and protected from moisture.

•The temperature around the receiver must be between –5˚ and 35˚ C (23˚ and 95˚ F).

•Make sure there is good ventilation around the receiver. Poor ventilation could cause overheating and damage the receiver.

Handling the receiver

•Do not insert any metal object into the receiver.

•Do not disassemble the receiver or remove screws, covers, or cabinet.

•Do not expose the receiver to rain or moisture.

Checking the Supplied Accessories

Check to be sure you have all of the following items, which are supplied with the receiver.

The number in the parentheses indicates quantity of the pieces supplied.

•Remote Control (1)

•Batteries (2)

•AM Loop Antenna (1)

•FM Antenna (1)

•Audio Signal Attenuating Cord (1)

•AC Plug Adaptor (1) (except for People’s Republic of China)

If anything is missing, contact your dealer immediately.

Setting the Voltage Selector Switch

Before connections, always do the following first if necessary.

How to set the voltage selector:

 

 

230 – 240V

Set the correct voltage for your area with the voltage

 

 

 

 

 

 

 

 

 

 

 

 

selector switch on the rear panel. Use a screw driver to

127V

 

 

 

 

 

rotate the switch so the number the arrow is pointing at is

 

 

 

 

 

 

 

 

 

 

220V

the same as the voltage where you are plugging in the

 

 

 

 

 

 

 

 

 

 

receiver.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

110V

 

 

 

 

 

 

LINE VOLTS

English

4

Page 6 Page 8
Image 7
Page 6 Page 8
Contents RX-884PBK Precaución English Español Português Table of Contents Using the DSP Modes Parts Identification Remote ControlFront Panel Locations How to set the voltage selectorGetting Started GeneralAM Antenna Connections Connecting the FM and AM AntennasGetting Started FM Antenna ConnectionsConnecting the Speakers Connecting the front speakersConnecting the subwoofer speaker Connecting the rear and center speakersUse front speakers with 4 16 ohm impedance Case 1 When you connect only one set of front speakersCase 2 When you connect two sets of front speakers About the speaker impedanceAudio component connections Connecting Audio/Video ComponentsAnalog connections Audio Components Video ComponentsVideo components Video component connectionsConnecting DVD player Digital 1 coaxial For Digital connectionsPutting Batteries in the Remote Control Connecting the Power CordTo shut off the power completely Press Power to set it in the Ñoff positionOn the front panel From the remote controlTurning the Power On and Off Standby Basic OperationsSelecting different sources for picture and sound Adjusting the VolumeBasic Operations Press one of the source selecting buttons directlyListening only with headphones From the remote control onlyOn the front panel only Keys are activated for sound adjustments Attenuating the Input SignalAdjusting the Subwoofer Output Level Display changes to show the current settingChanging the Source Name Basic SettingsSelecting the Input Mode Selecting the DBS tuner as the sourceListening at Low Volume Loudness Basic SettingsAdjusting the Front Speaker Output Balance Setting the Subwoofer InformationSPK Rear Speaker appears on the display Digital Input Digital in Terminal SettingSetting the Speakers for the DSP Modes Front, Center, and Rear Speaker SettingRear Delay Time Setting Center Delay Time SettingCrossover Frequency Setting Dynamic Range Compression Setting Low Frequency Effect Attenuator SettingOne Touch Operation To store the sound settingsTo recall the sound settings To cancel the One Touch Operation functionTo select the 10 kHz interval Setting the AM Tuner Interval SpacingTuning in Stations Manually Receiving Radio BroadcastsTo tune in a preset station Using Preset TuningTo store the preset stations To erase a stored preset stationPress FM Mode on the front panel or FM Mode Selecting the FM Reception ModeMute on the remote control Character is flashing after you have assigned a name Assigning Names to Preset StationsPress Tuner PRESET, while a character you want is FlashingSelecting Your Favorite SEA Mode Using the SEA ModesTo cancel the SEA mode To erase a stored adjustment Using the SEA ModesCreating Your Own SEA Mode To recall your own SEA adjustmentOn Surround mode Using the DSP ModesOn the 3D-PHONIC mode On the DAP modeTurn Multi JOG until the mode 3D Action or 3D Using the DSP ModesUsing the 3D-PHONIC Modes Press DSP ModeAs you turn it, the effect level changes as follows To cancel the 3D-PHONIC modePress Effect to select the effect level Press Surround Mode repeatedly until the mode 3DAction or 3D DIGITAL, 3D DRAMA, or 3D Theater You want appears on the displayUsing the DAP Modes Want appears on the display To cancel the DAP modePress Surround Mode repeatedly until the mode you Adjust the speaker output levels as followsPress Surround Mode repeatedly until PRO Logic Using the Dolby Digital and Dolby Pro Logic ModesOr Dolby Digital appears on the display Press Cntr Tone to select the center tone level you want To cancel the Surround modePress Test to start checking the speaker output balance Press Test again to stop the test tonePress Dolby Surround again so that Surround OFF appears Press Dolby Surround so that the lamp on the buttonLights up Turn Multi JOG to select the center tone level you wantUsing the Theater Surround Mode To cancel the Theater Surround mode Center tone adjustment affects the mid-frequencyDSP and Theater indicators also light up on the display SOFT2 SOFT1 Flat SHARP1 Selecting the Different Sources for Picture and Sound Using the On-Screen MenusWhen you select OSD, see Selecting the Source to Play Also seeSound Control menu appears on the TV Adjusting the Front Speaker Output Balance Also seeListening at Low Volume Loudness Also see Attenuating the Input Signal Also seeFor DAP modes Live CLUB, Dance CLUB, HALL, Pavilion Using the On-Screen MenusAdjusting the Subwoofer Output Level Also see For 3D-PHONIC modesFor Theater Surround and Digital Theater Surround Selecting Your Favorite SEA Mode Also seeFor Dolby Surround Pro Logic For Dolby DigitalBasic Settings Creating Your Own SEA Mode Also seePress SET to store the setting into the SEA Usermode Operating the Tuner Storing the Preset Stations Also seeCharacter entry screen appears Assigning Names to the Preset Stations Also seeTuner Control menu appears again Synchronized Recording Compu Link Remote Control SystemRemote Control through the Remote Sensor on the Receiver Automatic Source SelectionAdditional Functions Text Compu Link Remote Control SystemDisplaying the Disc Information on the TV screen Disc Search Only for CD PlayerShowing the Disc Information on the TV Screen OperationsSearch a disc by its disc title Text Compu Link Remote Control SystemSearching a Disc Only for the CD player Search a disc by its performerGenre Search screen appears Going back to the Disc Title Search screen Press ExitSearch a disc by its genre Press on Screen Control %/ Þ to move to GENRE, then pressUser File screen appears on the TV Using your own User FilesGoing back to the User File screen Press Exit To move to Shift , then press SET Entering the Disc InformationFor the CD Player with the disc memory function Title Input Performer screen appears on the TVEnter the disc title, referring to steps 3 and 4 on For the MD recorderEnter the song title, referring to steps 3 and 4 on Operating JVC’s Audio/Video Components Cassette deck Operating JVC’s Audio/Video ComponentsCD player-changer TurntableREC VCR1 the VCR connected to the VCR1 jacksDVD player Sets the input mode either TV or Adjusts the volumeTurns on or off the TV Try to operate your TV by pressing TV/CATV/DBS Operating Other Manufactures’ Components10, 0, 100++10 Operating Other Manufactures’ ComponentsPauses Starts playbackTry to operate your VCR by pressing VCR1 Manufacturers’ codes for TV Problem Possible Cause Solution TroubleshootingAmplifier SpecificationsVideo Important for mains AC line

RX-884PBK specifications

The JVC RX-884PBK is a powerful and versatile audio receiver that has garnered attention for its impressive features tailored to both casual listeners and dedicated audiophiles. Designed with a sleek and modern aesthetic, this receiver fits seamlessly into any home entertainment setup, delivering high-quality sound and an array of functionalities.

One of the standout features of the JVC RX-884PBK is its multi-channel audio support. This receiver is capable of delivering immersive surround sound, making it an excellent choice for home theater enthusiasts. With support for formats such as Dolby Digital and DTS, users can experience cinema-like audio directly in their living rooms, enhancing movies, music, and gaming experiences.

Power output is another highlight of the RX-884PBK, boasting significant wattage per channel that ensures clear and powerful audio across various speaker configurations. Whether you have a compact stereo setup or a full-fledged surround sound system, the receiver has the capacity to drive speakers effectively, providing dynamic range and depth in audio playback.

Connectivity is a crucial aspect of modern receivers, and the RX-884PBK does not disappoint. It offers multiple inputs, including analog, optical, and coaxial connections, allowing users to connect a variety of devices such as Blu-ray players, gaming consoles, and streaming devices. The built-in phono input also caters to vinyl enthusiasts, enabling direct connection to turntables for an authentic listening experience.

In terms of user interface, the JVC RX-884PBK features an intuitive control system that makes navigating through settings and configurations easy. The remote control adds an extra layer of convenience, allowing users to adjust settings from across the room without the need to get up.

Moreover, the receiver incorporates advanced technologies aimed at enhancing sound quality. With features such as digital signal processing, it can optimize audio playback for different environments. The equalizer settings provide users with the flexibility to customize sound according to personal preferences or specific genres.

In summary, the JVC RX-884PBK is a feature-rich audio receiver that caters to a wide range of listening preferences. Its powerful performance, extensive connectivity options, and user-friendly interface make it an ideal choice for anyone looking to elevate their home audio experience. Whether for movies, music, or gaming, this receiver is designed to deliver exceptional sound quality and enjoyment.
Top Page Image Contents