JVC RX-884PBK Press Surround Mode repeatedly until the mode 3D, You want appears on the display

Page 36

Using the DSP Modes

English

From the remote control:

1. Select and play the source encoded with Dolby Digital (bearing the mark

) or with Dolby Surround (bearing the mark DOLBY SURROUND ).

D I G I T A L

When you play back the source encoded with Dolby Digital and select the digital input for that source, the Ù DIGITAL indicator lights up on the display.

2. Press SURROUND MODE repeatedly until the mode — 3D

SURROUND

ACTION (or 3D DIGITAL), 3D DRAMA, or 3D THEATER

MODE

 

— you want appears on the display.

 

Each time you press the button, the DSP modes change as follows (the 3D-PHONIC and DSP indicators also light up on the display):

When the digital input is selected to play the source encoded with Dolby Digital:

DOLBY DIGITAL DIG-THEATER

OFF 3D DIGITAL HEADPHONE

For other sources:

PRO LOGIC THEATER LIVE CLUB DANCE CLUB HALL

OFF

PAVILION

3D THEATER 3D DRAMA 3D ACTION HEADPHONE

Note:

The 3D-PHONIC mode is not used with the other DSP modes such as the DAP mode and the Surround mode. When the 3D- PHONIC mode is turned on, the other DSP mode, if used, will be turned off.

Notes on the indications:

The indicator of the selected

 

DSP mode also lights up on

 

the display while selecting.

The PRO LOGIC indicator

 

lights up when the Dolby Pro

 

Logic decoder built in this

 

receiver is activated.

The Dolby Pro Logic decoder

 

is used not only for the analog

 

sources but also for the

 

sources encoded with Dolby

 

Digital in the following cases:

 

– When only front channel

 

signals are encoded.

3.Press SOUND CONTROL.

10 keys are activated for sound adjustments.

4.Press EFFECT to select the effect level.

Each time you press the button, the effect level changes as follows:

DSP EFFECT 1 DSP EFFECT 2 DSP EFFECT 3

DSP EFFECT 5

DSP EFFECT 4

As the number increases, the selected 3D-PHONIC mode becomes stronger.

To cancel the 3D-PHONIC mode

Press SURROUND MODE repeatedly until “OFF” appears. The 3D-PHONIC and DSP indicators go off from the display.

SOUND

CONTROL

EFFECT

7/P

– When front channel and

monaural rear channel

signals are encoded.

While the Dolby Pro Logic is activated for this type of Dolby Digital source, the Ù DIGITAL indicator goes off.

Note:

Once you have adjusted the 3D- PHONIC modes, it is memorized for each 3D-PHONIC mode.

33

Image 36
Contents RX-884PBK Precaución English Español Português Table of Contents Using the DSP Modes Remote Control Parts IdentificationFront Panel How to set the voltage selector Getting StartedGeneral LocationsConnecting the FM and AM Antennas Getting StartedFM Antenna Connections AM Antenna ConnectionsConnecting the front speakers Connecting the SpeakersConnecting the rear and center speakers Connecting the subwoofer speakerCase 1 When you connect only one set of front speakers Case 2 When you connect two sets of front speakersAbout the speaker impedance Use front speakers with 4 16 ohm impedanceConnecting Audio/Video Components Analog connectionsAudio Components Video Components Audio component connectionsVideo component connections Video componentsConnecting DVD player Digital connections Digital 1 coaxial ForConnecting the Power Cord To shut off the power completelyPress Power to set it in the Ñoff position Putting Batteries in the Remote ControlFrom the remote control Turning the Power On and Off StandbyBasic Operations On the front panelAdjusting the Volume Basic OperationsPress one of the source selecting buttons directly Selecting different sources for picture and soundFrom the remote control only Listening only with headphonesOn the front panel only Attenuating the Input Signal Adjusting the Subwoofer Output LevelDisplay changes to show the current setting Keys are activated for sound adjustmentsBasic Settings Selecting the Input ModeSelecting the DBS tuner as the source Changing the Source NameBasic Settings Adjusting the Front Speaker Output BalanceSetting the Subwoofer Information Listening at Low Volume LoudnessDigital Input Digital in Terminal Setting Setting the Speakers for the DSP ModesFront, Center, and Rear Speaker Setting SPK Rear Speaker appears on the displayCenter Delay Time Setting Rear Delay Time SettingCrossover Frequency Setting Low Frequency Effect Attenuator Setting Dynamic Range Compression SettingTo store the sound settings To recall the sound settingsTo cancel the One Touch Operation function One Touch OperationSetting the AM Tuner Interval Spacing Tuning in Stations ManuallyReceiving Radio Broadcasts To select the 10 kHz intervalUsing Preset Tuning To store the preset stationsTo erase a stored preset station To tune in a preset stationSelecting the FM Reception Mode Press FM Mode on the front panel or FM ModeMute on the remote control Assigning Names to Preset Stations Press Tuner PRESET, while a character you want isFlashing Character is flashing after you have assigned a nameUsing the SEA Modes Selecting Your Favorite SEA ModeTo cancel the SEA mode Using the SEA Modes Creating Your Own SEA ModeTo recall your own SEA adjustment To erase a stored adjustmentUsing the DSP Modes On the 3D-PHONIC modeOn the DAP mode On Surround modeUsing the DSP Modes Using the 3D-PHONIC ModesPress DSP Mode Turn Multi JOG until the mode 3D Action or 3DTo cancel the 3D-PHONIC mode As you turn it, the effect level changes as followsPress Surround Mode repeatedly until the mode 3D Action or 3D DIGITAL, 3D DRAMA, or 3D TheaterYou want appears on the display Press Effect to select the effect levelUsing the DAP Modes To cancel the DAP mode Press Surround Mode repeatedly until the mode youAdjust the speaker output levels as follows Want appears on the displayUsing the Dolby Digital and Dolby Pro Logic Modes Press Surround Mode repeatedly until PRO LogicOr Dolby Digital appears on the display To cancel the Surround mode Press Test to start checking the speaker output balancePress Test again to stop the test tone Press Cntr Tone to select the center tone level you wantPress Dolby Surround so that the lamp on the button Lights upTurn Multi JOG to select the center tone level you want Press Dolby Surround again so that Surround OFF appearsUsing the Theater Surround Mode Center tone adjustment affects the mid-frequency To cancel the Theater Surround modeDSP and Theater indicators also light up on the display SOFT2 SOFT1 Flat SHARP1 Using the On-Screen Menus When you select OSD, seeSelecting the Source to Play Also see Selecting the Different Sources for Picture and SoundAdjusting the Front Speaker Output Balance Also see Listening at Low Volume Loudness Also seeAttenuating the Input Signal Also see Sound Control menu appears on the TVUsing the On-Screen Menus Adjusting the Subwoofer Output Level Also seeFor 3D-PHONIC modes For DAP modes Live CLUB, Dance CLUB, HALL, PavilionSelecting Your Favorite SEA Mode Also see For Dolby Surround Pro LogicFor Dolby Digital For Theater Surround and Digital Theater SurroundCreating Your Own SEA Mode Also see Basic SettingsPress SET to store the setting into the SEA Usermode Storing the Preset Stations Also see Operating the TunerAssigning Names to the Preset Stations Also see Character entry screen appearsTuner Control menu appears again Compu Link Remote Control System Remote Control through the Remote Sensor on the ReceiverAutomatic Source Selection Synchronized RecordingText Compu Link Remote Control System Displaying the Disc Information on the TV screenDisc Search Only for CD Player Additional FunctionsOperations Showing the Disc Information on the TV ScreenText Compu Link Remote Control System Searching a Disc Only for the CD playerSearch a disc by its performer Search a disc by its disc titleGoing back to the Disc Title Search screen Press Exit Search a disc by its genrePress on Screen Control %/ Þ to move to GENRE, then press Genre Search screen appearsUsing your own User Files User File screen appears on the TVGoing back to the User File screen Press Exit Entering the Disc Information For the CD Player with the disc memory functionTitle Input Performer screen appears on the TV To move to Shift , then press SETFor the MD recorder Enter the disc title, referring to steps 3 and 4 onEnter the song title, referring to steps 3 and 4 on Operating JVC’s Audio/Video Components Operating JVC’s Audio/Video Components CD player-changerTurntable Cassette deckVCR1 the VCR connected to the VCR1 jacks RECDVD player Adjusts the volume Sets the input mode either TV orTurns on or off the TV Operating Other Manufactures’ Components Try to operate your TV by pressing TV/CATV/DBSOperating Other Manufactures’ Components 10, 0, 100++10Starts playback PausesTry to operate your VCR by pressing VCR1 Manufacturers’ codes for TV Troubleshooting Problem Possible Cause SolutionSpecifications AmplifierVideo Important for mains AC line

RX-884PBK specifications

The JVC RX-884PBK is a powerful and versatile audio receiver that has garnered attention for its impressive features tailored to both casual listeners and dedicated audiophiles. Designed with a sleek and modern aesthetic, this receiver fits seamlessly into any home entertainment setup, delivering high-quality sound and an array of functionalities.

One of the standout features of the JVC RX-884PBK is its multi-channel audio support. This receiver is capable of delivering immersive surround sound, making it an excellent choice for home theater enthusiasts. With support for formats such as Dolby Digital and DTS, users can experience cinema-like audio directly in their living rooms, enhancing movies, music, and gaming experiences.

Power output is another highlight of the RX-884PBK, boasting significant wattage per channel that ensures clear and powerful audio across various speaker configurations. Whether you have a compact stereo setup or a full-fledged surround sound system, the receiver has the capacity to drive speakers effectively, providing dynamic range and depth in audio playback.

Connectivity is a crucial aspect of modern receivers, and the RX-884PBK does not disappoint. It offers multiple inputs, including analog, optical, and coaxial connections, allowing users to connect a variety of devices such as Blu-ray players, gaming consoles, and streaming devices. The built-in phono input also caters to vinyl enthusiasts, enabling direct connection to turntables for an authentic listening experience.

In terms of user interface, the JVC RX-884PBK features an intuitive control system that makes navigating through settings and configurations easy. The remote control adds an extra layer of convenience, allowing users to adjust settings from across the room without the need to get up.

Moreover, the receiver incorporates advanced technologies aimed at enhancing sound quality. With features such as digital signal processing, it can optimize audio playback for different environments. The equalizer settings provide users with the flexibility to customize sound according to personal preferences or specific genres.

In summary, the JVC RX-884PBK is a feature-rich audio receiver that caters to a wide range of listening preferences. Its powerful performance, extensive connectivity options, and user-friendly interface make it an ideal choice for anyone looking to elevate their home audio experience. Whether for movies, music, or gaming, this receiver is designed to deliver exceptional sound quality and enjoyment.