Huffy AR64S-H manual Wichtig ¡IMPORTANTE

Page 51

8.

Tournez les extrémités non fixées des contrefiches du réservoir (2) vers l’extérieur jusqu'aux trous de

 

fixation du réservoir, comme illustré. Fixez les extrémités des contrefiches (2) sur le support de roue

(7), comme illustré. Reprenez la procédure de l’autre côté.

Die ungesicherten Enden der Tankverstrebungen (2) wie gezeigt nach außen zu den Befestigungslöchern im Tank drehen. Die Enden der Tankverstrebungen (2) wie gezeigt an der Radhalterung (7) befestigen. Das gleiche Verfahren auf der anderen Seite durchführen.

Haga girar los extremos no asegurados de los puntales del tanque (2) hacia fuera hasta los orificios de montaje del tanque como se muestra. Asegure los extremos de los puntales del tanque (2) al soporte de la rueda (7), como se muestra. Repita el procedimiento en el lado opuesto.

IMPORTANT!

WICHTIG!

¡IMPORTANTE!

NE SERREZ PAS LA VISSERIE À FOND.

DIE BEFESTIGUNGSTEILE NICHT FEST ANZIEHEN.

NO APRIETE COMPLETAMENTE EL HERRAJE.

2

18

2

51

18 51

AVERTISSEMENT !

WARNUNG!

¡ADVERTENCIA!

Il est obligatoire de s'y prendre à deux pour cette

7

procédure. SUIVEZ CET AVERTISSEMENT SOUS

 

 

PEINE D'ENCOURIR DES BLESSURES GRAVES

 

ET/OU DES DÉGÂTS MATÉRIELS.

 

Dieses Schritt muss von zwei Personen ausgeführt werden. EIN MISSACHTEN DIESER WARNUNG KANN ZU SCHWEREN VERLETZUNGEN UND/ODER SACHSCHÄDEN FÜHREN.

Se requieren dos personas para realizar este procedimiento. SI NO SE OBSERVA ESTA ADVERTENCIA SE PODRÍA OCASIONAR UNA lesión GRAVE Y/O DAÑOS A LA PROPIEDAD.

51

02/06

ID# M661144

Image 51
Contents Portable System Before YOU Start 02/06 ID# M661144 Safety Instructions Product Registration Get to know the basic parts of your basketball system Parts List See Hardware Identifier Hardware Identifier Bolts & Screws Hardware Identifier Nuts & Washers Hardware Identifier Plastic Spacers Caps & Clips Tools Required for this Section Nut P/N 203100, Carriage Bolts P/N Fig. a Align dimple of top pole section Dimple Hole Do not Tighten Completely Tighten ALL Components Completely Steps Tighten just until washers 17 stop moving FIG. a Section B Attach the Backboard 02/06 ID# M661144 Completed Assembly 02/06 ID# M661144 ID# M661144 02/06 USE EYE Protection When Installing Springs Install Slam Jam Rim to Backboard If Using Sand 2 Gallons of ANTI-FREEZE is not Required Section C Apply Height and Moving Label & Height Adjustment Section D Cover Parts List FIG. a Système portable Manuel de Lutilisateur Tubular y casquillos se Recomiendan casquillos profundos ID# M661144 02/06 Achtung Consignes DE Sécurité Stop Halt Avis AUX Personnes Chargées DU Montage Remarque Hinweis Nota #16 #19 #29 #63 Item #23 #47 #39 #40 1 #18 #12 1 #52 #44 #55 #57 #56 #54 1/2 Boulon ordinaire no de réf Hinweis / Nota Vorsicht ¡PRECAUCIÓN Renfoncement Einbuchtung Concavidad Trou Loch Orificio Avertissement Warnung ¡ADVERTENCIA Wichtig ¡IMPORTANTE Wichtig ¡IMPORTANTE Wichtig ¡IMPORTANTE Avant Vorderseite Lado Frontal Wichtig ¡IMPORTANTE Outils Requis Pour Cette Section Page Assemblage Terminé Fertige Montage Conjunto Completado Hinweis / Nota 02/06 ID# M661144 ID# M661144 02/06 Avertissement Warnung ¡ADVERTENCIA ID# Installez le cerceau Slam Jam sur le panneau Vorsicht ¡PRECAUCIÓN Remarque Hinweis Nota ID# Liste DES Pièces / Teileliste / Lista DE Piezas Remarque / Hinweis / Nota ABB. a FIG. C