JVC RX-DP20VBK manual Press Text Display while CD or MD is selected as the source, Zone 2 Learn

OPERATIONS

To use this remote control system, you need to connect the Zone 1 TV to the MONITOR OUT jack (see page 14) and the Zone 2 TV to the ZONE 2 MONITOR OUT jack (see page 19), and set the TV’s input mode to the proper position to which the receiver is connected.

Make sure you have connected the CD player or MD recorder equipped with the TEXT COMPU LINK remote control system. If not, you cannot use the following functions.

IMPORTANT:

Check the following before or while using the buttons and controls.

•When using the remote control:

–Set the ZONE 1/ZONE 2 (LEARN/TRANSMIT) selector to “ZONE 1” or “ZONE 2” correctly.

–Check the indication shown on the remote’s display when you press a button—this indicates the remote control operation mode together with multi-room operation mode (either ZONE 1 or ZONE 2) for a while.

LEARN TRANSMIT					LEARN	TRANSMIT
ZONE 1		ZONE 2		ZONE 1		ZONE 2
LEARN	TRANSMIT			LEARN	TRANSMIT
		STANDBY	ON			STANDBY	ON
ZONE 1	ZONE 2			ZONE 1	ZONE 2
ZONE 1	ZONE 2	TV/CATV/DBS	VCR 1	ZONE 1	ZONE 2	TV/CATV/DBS	VCR 1
ON/OFF	ON/OFF			ON/OFF	ON/OFF
		STANDBY/ON	STANDBY/ON			STANDBY/ON	STANDBY/ON
ZONE 1					ZONE 2

Ex. When you press TEXT	Ex. When you press TEXT
DISPLAY with ZONE 1/	DISPLAY with ZONE
ZONE 2 (LEARN/	1/ZONE 2 (LEARN/
TRANSMIT) selector set	TRANSMIT) selector
to “ZONE 1.”	set to “ZONE 2.”

TEXT	SET
DISPLAY

EXIT

Text display operation buttons

Showing the Disc Information on the TV Screen (Either in Zone 1 or in Zone 2)

Press TEXT DISPLAY while “CD” or “MD” is selected as the source.

The Disc Information screen appears on the TV.

Disc Information screen

1

	6
2	7

3	8
4
5	9

1Source name: CD or MD

2Select or , then press SET to change the disc.

3 Track numbers and track titles.

•When you move to a track number, you can change the track information by pressing @ / #. Each time you press the button, track information alternates between its track title and its performer. (You can also start playing the track by pressing

SET.)

4Select this (move in front), then press SET to go to the DISC SEARCH screen (see page 65).

5Select this (move in front), then press SET to go to the TITLE INPUT screen (see page 66).

6This appears only when a CD Text is selected.

7Disc information such as the disc title, performer, music genre, etc.

When this is selected ( in front), you can change the disc information by pressing @ / #. Each time you press the button, disc information (see “Note on 7”) changes.

8Select or , then press SET to change the track.

9Usable buttons and their functions for the current selection. Indication here will change according to what is currently

selected ( in front) on the screen. See “Note on 9.”

Note on 7:

The following information will appear on the display:

•For CD Texts—Disc title, Performer, Genre, Song writer, Composer, Arranger, Message

Only recorded information will be shown. If there is no data, “NO DATA” will appear.

•For MDs—Disc title

If there is no data, “NO DATA” will appear.

Note on 9:

For example, the SET button will be used to start play (PLAY), to go to the next screen (ENTER), and to determine the selection (ENTER).

To exit from the Disc information screen

Press EXIT.

Notes:

•The on-screen display will disappear in the following cases:

–if no operation is done for about 10 minutes.

–if you do any operation other than explained in this section.

•To control the MD recorder using the TEXT COMPU LINK remote control system, you have to change the source name shown on the display from “TAPE” to “MD.” (See page 27.)

•Some special characters and marks cannot be displayed correctly.

64