JVC RX-DP20VBK manual AV Compu Link Remote Control System, Connections 2 AV Compu Link Connection

Page 71

AV COMPU LINK Remote Control System

This receiver is equipped with the AV COMPU LINK-III. The AV COMPU LINK remote control system allows you to operate JVC video components (TV, VCR, and DVD player) through the receiver. To use this remote control system, you need to connect the video components you want to operate, following the procedure below.

•Refer also to the manuals supplied with your video components.

1.If you have already plugged your VCR 1 (VCR connected to the VCR 1 jacks), DVD player, TV, and this receiver into the AC outlets, unplug their AC power cords first.

2.Connect the IR signal transmitter (supplied) to the IR OUT on the rear, and place it so that it is aimed at the remote sensor(s) on the target video component(s).

•See “CONNECTIONS 1” below (and page 17 for details).

3.Connect your VCR 1, DVD player, TV, and this receiver as follows, using cables with monaural mini-plugs (not supplied).

•See “CONNECTIONS 2” below.

4.Connect the audio input/output jacks on VCR 1, DVD player, TV, and this receiver using the cables with RCA pin plug.

•See pages 13 to 15.

5.Connect the video input/output jacks on VCR 1, DVD player, TV, and this receiver, using the cables with RCA pin plugs, with S-video plugs or with component video plugs.

•See “CONNECTIONS 3” on the next page (and pages 13 to 15 for details).

6.Plug the AC power cords of the components into the AC outlets.

7.When turning on the TV for the first time after the AV COMPU LINK connection, turn the TV volume to the minimum using the TV volume control on the TV.

8.Turn on the other connected components first, then turn on this receiver.

•When turning on the VCR 1, use the remote control supplied with this receiver—press VCR 1 (STANDBY/ON).

CONNECTIONS 1: IR Signal Transmitter Connection

Target video component(s)

 

 

 

 

 

On the rear panel

RX-DP20VBK

 

 

 

 

 

COMPU

AV

TEXT

IR

CTRL

 

LINK-4

COMPU COMPU

OUT

 

OUT

 

(SYNCHRO) LINK-

LINK

+12V

 

 

 

 

 

 

IR

10mA MAX

 

 

 

 

IN

 

 

At an angle of

 

 

 

 

 

approx. 60°

 

 

 

 

 

IR signal transmitter

 

 

 

 

 

CONNECTIONS 2: AV COMPU LINK Connection

VCR 1

DVD player

VHS

COMPU

AV

TEXT

IR

CTRL

DVD

LINK-4

COMPU

COMPU

OUT

OUT

 

(SYNCHRO)

LINK-

LINK

+12V

 

 

AV

 

 

COMPU LINK

IR

10mA MAX

 

IN

 

AV

COMPU LINK

RX-DP20VBK

Notes:

TV

AV COMPU LINK EX

AV

COMPU LINK III

CAUTION:

When connecting the TV with the AV COMPU LINK remote control system, connect the receiver to the AV COMPU LINK EX or AV COMPU LINK III terminal.

DO NOT connect the receiver to the AV COMPU LINK RECEIVER/ AMP terminal.

•The AV COMPU LINK remote control system cannot control the DBS tuner connected to the TV SOUND/DBS IN jacks, and video components connected to the VIDEO and VCR 2 IN jacks on the receiver.

•When connecting only the VCR 1 or DVD player to this receiver, connect it directly to the receiver using a cable with the monaural mini- plugs.

•When connecting the receiver and the TV with AV COMPU LINK EX terminal by using the component video cables, you cannot use Automatic Selection of TV’s Input Mode (see page 70).

68

Page 70 Page 72
Image 71
Page 70 Page 72
Contents LVT0965-001AJ RX-DP20VBK23.5 kg / 52.0 lb For the main unit Introduction Features PrecautionsTable of Contents To open the front door Parts IdentificationFront Panel Display Window96/24 indicator Dual indicatorAnalog indicator Dgtl Auto indicatorRear Panel Remote Control Getting Started Before InstallationChecking the Supplied Accessories Connecting the FM and AM AntennasAM Antenna Connections Connecting the SpeakersBasic connecting procedure Front speakers and center speaker Front speakers Center speaker Right / LeftFront speakers Zone 1 speaker layoutLeft surround Connecting a subwooferPowered Enhance your audio systemAnalog Connections Connecting Audio/Video ComponentsExternal 7.1-channel Output component Decoder Or DVD player When attaching the front Terminal coverWhen removing the cover When using the digital input terminalVHS/S-VHS/VHS VCR VCRsDBS tuner TV and/or DBS tunerDVD player When you connect the DVD player with stereo output jacksDVD player Digital input terminals Digital ConnectionsDigital output terminal Setting Up the IR Signal Transmitter Using the RF Rod Antenna and IR Signal TransmitterFind a place where you can attach the IR signal transmitter Setting Up the RF Rod AntennaReplace the cover Putting Batteries in the Remote ControlConnecting the Power Cord When using the remote control in the darkConnection Å Connection ı Power amplifierMulti-Room Operations Required Connections for ZoneBasic Operating Procedure for Zone Sound through the Zone 2 front Speakers Turn Master Volume toPress Zone 2 ON/OFF so that Zone 2 ON/OFF lamp lights upZone 1 Main Room Operations Turning the Power On and Off StandbyTo turn on the power, press To turn off the power into standby modeSelecting the Zone 1 Source to Play Canceling the Zone 1 OperationsSpeaker and signal indicators on the display Setting onSelecting different sources for picture and sound Adjusting the Zone 1 VolumeMode Selecting the Analog or Digital Input ModeActivating the Zone 1 Front Speakers Front door so that the Input ATT Attenuating the Input SignalIndicator lights up on the display Press and hold Input ATT insideChanging the Source Name Changing the Display BrightnessMaking Sounds Natural Turning Analog Direct On and OffRecording a Source Using the Sleep TimerBasic adjustment auto memory Press Sleep repeatedlyFront door so that Zone Previously selected Zone Last Zone Zone 2 volume Source appears Level appearsZone 2 Sub-room Operations Press Zone 2 Control insideTo use this receiver for Zone 2 operations Canceling the Zone 2 OperationsTo stop Zone 2 operations and sounds through Zone 2 speakers, press Zone 2 ON/OFF so thatDVD Adjusting the Zone 2 VolumeSelected source name Zone 2 volume Level appears Selecting the Zone 2 Source to PlayMuting the Zone 2 Sound Activating the Zone 2 Front SpeakersPress Zone 2 to activate the Zone Front speakersPress FM/AM Tuning in to Stations ManuallyEx. When you press FM/AM With Zone 1/ZONE Receiving Radio BroadcastsSelecting the FM Reception Mode Using Preset TuningSetup Menu Configuration Basic SettingsButton To do Operation through On-Screen Display MenusMenu operation buttons Press SET Menu Operating ProcedurePress Setup Menu 1SPK Setting the Speakers-SPEAKER SettingAdjusting the Speaker Channel Output Levels-CHANNEL Level YESFront R Level AutoOFF Front L LevelLFE Setting the Speaker DistanceSetting the Bass Sounds-SUBWOOFER For each speakerClose Setting the THX Audio-THX Audio SetupApart Selecting the Dual Mono Sound-DUAL Mono Setting the Surround Channel Output Speakers-SURR CH OUTSetting the Audio Delay Level-AUDIO Delay Setting the Digital Input/Output TerminalsPCM Setting the Video Input TerminalsSetting the Zone 2/Speakers 2 Usage -ZONE 2/SPEAKER Turning On and Off the Video OutputText Memorizing the Volume Level for Each Source-ONE Touch OPESuperimposing the Menus-SUPERIMPOSE Showing the Text Information on the Display-FL DisplayAdjustment Menu Configuration Sound AdjustmentsOr an item on a submenu downwards or Adjust MenuDisplay or erase the Adjustment Menu Select a submenu on the Adjustment MenuSet other items on the same submenu if necessary Press Adjust MenuPress fi or % Down or UP repeatedly To select the desired submenuMID Adjustment procedureSubmenu items BassWhen one of the DSP modes except ALL CH Stereo is activated Setting the Midnight Mode-MIDNIGHT ModeAdjusting the Various Effects Overall level of the effect 1 to When Dolby Pro Logic II Music is activatedWhen Neo6 Music is activated Press Liveness repeatedly to adjustIntroducing the Surround and THX Modes Using the Surround and THX ModesReproducing Theater Ambience DTS Extended Surround DTS-ES Dolby Digital EXDolby Pro Logic DTS Digital SurroundES/EX/7.1 Available Surround and THX Modes Applicable to the Various SoftwareZone Available THX Mode Incoming Signal Type 2-channel Available Surround ModeEXES7.1 on Activating the Surround and THX ModesAbout Dialog Normalization Activating the 7.1-channel reproductionTo adjust the speaker output level using the remote control Press Surround to activate the Surround ModeTo cancel the Surround mode Ex. When Dolby Digital is activated3D Headphone Mode Press THX to activate the THX modeTo cancel the THX mode without canceling the Surround mode To cancel the THX and Surround modesIntroducing the DSP Modes Using the DSP ModesHeadphone Mode Reproducing the Sound FieldActivating the DSP Modes To adjust the DSP effectsTo cancel the DSP modes Press Effect repeatedly to adjust the levelPlayback Modes Using the Analog Multi-channel Playback ModeActivating the Analog Multi-channel Supplied for this receiver, the receiver Compu Link Remote Control SystemCassette deck MD recorderPress the play 3 button on the CD player When you turn off the Zone 1 sound by pressingWhen you turn off the Zone 2 source by pressing At the same timeDisc Search Only for CD Player Text Compu Link Remote Control SystemRX-DP20VBK Displaying the Disc Information on the TV screenZone 2 Learn Press Text Display while CD or MD is selected as the sourceDisc Information screen To exit from the Disc information screenPress SET again Press Text Display while CD is selected as the sourcePress % / fi to move to SEARCH, then press Press % / fi to move to Performer Then press SETPress % / fi to move to Title INPUT, then press SET Press % / fi to move to SEARCH, then press SETPress % / fi to move To GENRE, then Press SET Press % / fi to move To the genre youPress % / fi to move to Title Input Then press SET Enter the disc title, referring to steps 3Press % / fi to move to the genre you want, then press SET Press Text Display while MD is selected as the sourceConnections 2 AV Compu Link Connection AV Compu Link Remote Control SystemConnections 1 IR Signal Transmitter Connection IR signal transmitterOne-Touch Video Play Connections 3 Video Cable ConnectionCase One-Touch DVD Play Automatic Power On/Off StandbyAutomatic Power On When you turn off the Zone 2 sound by pressingSound control section Amplifier Operating JVC’s Audio/Video ComponentsOperating Audio Components TunerCD recorder CD playerCD player-changer TurntableDVD player Operating Video ComponentsVCR VCR connected to the VCR 1 jacks ¶ RECOperating Other Manufacturers’ Equipment Changing the Preset Signal CodesButtons 1-9, Enter a manufacturer’s code usingPress and hold VCR Press VCRRelease Audio Standby Enter a manufacturer’s code using buttons 1-9,Press and hold Audio Standby Press DVD Release Audio onManufacturer Codes Manufactures’ codes for DBS tuner Manufacturer CodesManufactures’ codes for Catv converter Manufacturer Codes Manufactures’ codes for VCRZone 1/ZONE 2 selector to Storing the Remote Signals ManuallyTo store the signals Set the LEARN/TRANSMITFor the Zone 1 operations For the Zone 2 operations Control\and To use the stored signalsTo erase the stored signals Press the desired buttonSurround/THX TroubleshootingProblem Possible Cause Solution Multi-room operations Zone1/ZoneGeneral CATV/DBSFM/AM Audio SpecificationsOutput Power AmplifierGeneral VideoFM tuner IHF AM tunerLimited Warranty Authorized Service Centers RX-DP20VBK
Top Page Image Contents