Weider 831.159530 user manual Locate and open the parts bag labeled Seat Assembly

Page 20

Seat Assembly

53.Locate and open the parts bag labeled “SEAT ASSEMBLY.”

Press a 1 1/2” Square Inner Cap (100) into the bottom of a Seat Bracket (11). Press two 1” x 2” Inner Caps (70) into the ends of the Seat Bracket.

Insert a 1/4” x 1 3/4” Carriage Bolt (93) into the center hole of a Support Plate (57). Attach the Support Plate to a Seat (25) with two 1/4” x 3/4” Screws (90). Attach the Seat to the Seat Bracket

(11)with the Carriage Bolt, a 1/4” Washer (84), and a 1/4” Nylon Locknut (106). Attach the other end the Seat to the Seat Bracket with 1/4” x

1 3/4” Screw (98) and a 1/4” Washer (84).

Loosen the Adjustment Knob (not shown) by turn- ing it counterclockwise, and pull it out as far as possible. Insert the Seat Bracket (11) into the Butterfly Seat Frame (10) and align an adjustment hole with the Adjustment Knob. Snap the Knob into the adjustment hole and turn it clockwise until tight.

54.Attach the Butterfly Backrest (53) to the Butterfly Upright (4) with two 1/4” x 2 3/4” Screws (94) and two 1/4” Washers (84).

55.Press a 1 1/2” Square Inner Cap (100) into the bottom of a Seat Bracket (11). Press two 1” x 2” Inner Caps (70) into the ends of the Seat Bracket.

Insert a 1/4” x 1 3/4” Carriage Bolt (93) into the center hole of a Support Plate (57). Attach the Support Plate to a Seat (25) with two 1/4” x 3/4” Screws (90). Attach the Seat to the Seat Bracket

(11)with the Carriage Bolt, a 1/4” Washer (84), and a 1/4” Nylon Locknut (106). Attach the other end the Seat to the Seat Bracket with 1/4” x

1 3/4” Screw (98) and a 1/4” Washer (84).

Loosen the Adjustment Knob (51) by turning it counterclockwise, and pull it out as far as possi- ble. Insert the Seat Bracket (11) into the Press Seat Frame (12) and align an adjustment hole with the Adjustment Knob. Snap the Knob into the adjustment hole and turn it clockwise until tight.

53

 

25

 

 

93

 

57

 

90

11

70

70

84

106

84

100

98

10

 

54

 

 

94

 

84

53

4

 

84

 

94

55

 

25

 

 

93

 

57

 

90

11

70

70

84

100 106

84

98

 

12

 

 

51

20

Image 20
Contents Model No Serial No SEARS, Roebuck and CO. Hoffman ESTATES, ILTable of Contents Important Precautions Before YOU Begin Assembly Make Assembly Easier for YourselfDo not tighten the Nylon Locknuts yet Frame AssemblyLocate and open the parts bags labeled Frame Assembly 1 Do not tighten the Nylon Locknuts 64, 74 yet Do not tighten the 3/8 Nylon Locknuts 74 yetWeight Guides 33. Be sure the weight tubes Are near the top of the Weight CarriagesGuides 33 as shown in step Nylon Locknut 74. Do not tighten the Nylon Locknuts yetDo not tighten the 5/16 Nylon Locknuts 64 yet Tighten all of the Nylon Locknuts 64, 74 used in steps 1 toArm Assembly AssemblyLocate and open the parts bag labeled ARM Indicated axle. Be sure the upper endPage Cable Assembly Page Trap is oriented as shown Page Page Pulley make sure that the large tabs are Cable Trap is oriented as shownPulley Page Seat Assembly Locate and open the parts bag labeled Seat AssemblyPage Page Adjustments Adjusting the SeatAdjusting the Press Backrest Adjusting the Press PlateAttaching the LAT BAR Using the Weight CarriageAttaching the Curl PAD Weight Resistance Chart Cable Diagrams TROUBLE-SHOOTING and Maintenance Tightening the CablesFull 90 DAY Warranty Model NoSEARS, Roebuck and CO., Hoffman ESTATES, IL SEARS, Roebuck and CO., Dept WA, Hoffman ESTATES, ILRemove this Part Identification Chart from the Manual Page Part LIST-Model No Page Remove this Part LIST/EXPLODED Drawing from the Manual Qty Description Key No. Qty 106 100 101 103 105 107 102 2730 104