Weider WESY39310 user manual

Page 13

22.See the inset drawing. Attach a 3 1/2” Pulley (15) and a Cable Trap (66) to the upper hole in a Long “U”-Bracket (57) with a 3/8” x 2” Bolt (12) and a 3/8” Nylon Locknut (21). Be sure that the Cable Trap is inside the Long “U”-Bracket. Note: This may come pre-assembled.

Route the High Cable (58) through the Long “U”- Bracket (57) and the 3 1/2” Pulley (15) shown in the inset drawing. Be sure that the Cable is in the groove of the Pulley and that the Cable and Pulley move smoothly.

23.Wrap the High Cable (58) around a 3 1/2” Pulley (15). Attach the Pulley to the bracket on the Top Frame (55) with a 3/8” x 2” Bolt (12) and a 3/8” Nylon Locknut (21). Be sure that the Cable is in the groove of the Pulley and that the Cable and Pulley move smoothly.

24.Attach the High Cable (58) to a Small “U”-Bracket

(71)with a 1/4” Nylon Locknut (2) and a 1/4” Washer

(10).Do not completely tighten the Nylon Locknut. It should be threaded onto the end of the Cable only a couple of turns, as shown in the inset drawing.

Attach the Small “U”-Bracket (71) to the indicated Weight Tube (63) with a 5/16” x 1 3/4” Bolt (24) and a 5/16” Nylon Locknut (3).

13

22

 

 

 

58

 

66

15

 

21

 

15

 

 

57

12

58

 

 

 

57

 

23

 

 

 

 

12

 

Bracket

58

 

 

15

 

 

55

21

 

 

24

 

 

 

58

 

 

3

 

 

 

24

 

71

 

 

63

 

 

58

10

71

 

 

 

 

10

2

 

 

 

2

 

Image 13
Contents Model No. WESY39310 Serial No QUESTIONS?Customer HOT Line Table of Contents Important Precautions Decal No Before YOU BeginChart located in the center of this manual AssemblyFollowing Tools not Included are Required for Assembly Questions?Do not tighten the Nylon Locknuts yet Locknuts yetTighten all 5/16 Nylon Locknuts 3 used in steps Weight Guides are at the top, as shown On the Weight Tube is sitting in the pin grooves Top WeightHoles in the Weight Guides are at the top, as Shown Nylon Locknut the Leg Press Arm must be able to pivot freely Locate and open the parts bag labeled ARM AssemblyNylon Locknut yet Cable Assembly Locknut the Pulley Bracket must be able to move freely Page LOW PULLEY. Route the Low Cable under Locate the Low Cable 23 and the bag labeled2 Low Pulley 76. Attach the Pulley X 9/16 Spacer 7 to the Press Frame 17 withPage Cable Trap is positioned to hold the Cable in place Page Locate and open the parts bag labeled Seat Assembly Seat AssemblyPage Page Changing the Weight Setting AdjustmentsAttaching and Removing the Seat Adjusting the LEG Press PlateAttaching the LEG Lever to the LOW Pulley Station Plates Weight Resistance ChartTightening the Cables TROUBLE-SHOOTING and MaintenanceTOP View Cable DiagramsLeg Press Cable Military Press Cable 72 and Leg Press CableExploded DRAWING-Model No. WESY39310 Page Page Part LIST-Model No. WESY39310 Exploded Drawing Limited Warranty Ordering Replacement PartsIcon Health & FITNESS, INC., 1500 S W., LOGAN, UT