Weider WESY39310 user manual Assembly, Chart located in the center of this manual, Questions?

Page 5

ASSEMBLY

Before beginning assembly, carefully read the following information and instructions:

Due to the many features of the weight system, assembly will require about six hours. By setting aside plenty of time and by deciding to make the task enjoyable, assembly will go smoothly. You may want to assemble the weight system over a couple of evenings.

Place all parts of the weight system in a cleared area and remove the packing materials; do not dispose of the packing materials until assembly is completed.

Assembly is divided into four stages: 1) frame assembly, 2) press and butterfly arm assembly, 3) cable and pulley assembly, and 4) seat and backrest assembly. The hardware for each stage is packaged separately.

Wait until you begin each assembly stage to open the parts bag labeled for that assembly stage.

For help identifying the small parts used in assembly, use the PART IDENTIFICATION

CHART located in the center of this manual.

Note: Some small parts may have been pre- attached for shipping. If a part is not in the parts bag, check to see if it has been pre-attached.

Tighten all parts as you assemble them, unless instructed to do otherwise.

Assembly requires two persons. For your conve- nience and safety, assemble the weight system with the help of another person.

As you assemble the weight system, be sure that all parts are oriented as shown in the drawings.

THE FOLLOWING TOOLS (NOT INCLUDED) ARE REQUIRED FOR ASSEMBLY:

• Two (2) adjustable wrenches

• One (1) standard screwdriver

• One (1) phillips screwdriver

• One (1) rubber mallet

Lubricant, such as grease or petroleum jelly, and soapy water will also be needed.

Assembly will be more convenient if you have the following tools: A socket set, a set of open-end or closed-end wrenches, or a set of ratchet wrenches.

Questions?

If you have questions after reading the assembly instructions, please call our Customer Service Department toll-free at 1-800-999-3756, Monday through Friday, 6 a.m. until 6 p.m. Mountain Time.

FRAME ASSEMBLY

1.Before beginning, be sure that you have read and understand the information in the box above.

Locate and open the parts bag labeled “FRAME ASSEMBLY.”

Press two 2” Square Outer Caps (51) onto the indi- cated locations on the Stabilizer (5). Press a 2” Square Inner Cap (27) into the end of the Base (4).

Insert six 5/16” x 2 1/2” Carriage Bolts (1) up through the Stabilizer (5). Insert two 5/16” x 2 1/2” Carriage Bolts up through the Base (4).

Attach the Base (4) to the Stabilizer (5) with two 5/16” x 2 3/4” Bolts (11), two 5/16” Washers (8), and two 5/16” Nylon Locknuts (3). Do not tighten the

Nylon Locknuts yet.

1

 

 

 

 

11

51

 

8

 

 

5

 

 

1

 

 

3

 

1

4

51

 

 

 

 

 

1

 

 

27

5

Image 5
Contents Customer HOT Line QUESTIONS?Model No. WESY39310 Serial No Table of Contents Important Precautions Decal No Before YOU BeginChart located in the center of this manual AssemblyFollowing Tools not Included are Required for Assembly Questions?Do not tighten the Nylon Locknuts yet Locknuts yetTighten all 5/16 Nylon Locknuts 3 used in steps Holes in the Weight Guides are at the top, as Shown On the Weight Tube is sitting in the pin grooves Top WeightWeight Guides are at the top, as shown Nylon Locknut the Leg Press Arm must be able to pivot freely Locate and open the parts bag labeled ARM AssemblyNylon Locknut yet Cable Assembly Locknut the Pulley Bracket must be able to move freely Page LOW PULLEY. Route the Low Cable under Locate the Low Cable 23 and the bag labeled2 Low Pulley 76. Attach the Pulley X 9/16 Spacer 7 to the Press Frame 17 withPage Cable Trap is positioned to hold the Cable in place Page Locate and open the parts bag labeled Seat Assembly Seat AssemblyPage Page Changing the Weight Setting AdjustmentsAttaching the LEG Lever to the LOW Pulley Station Adjusting the LEG Press PlateAttaching and Removing the Seat Plates Weight Resistance ChartTightening the Cables TROUBLE-SHOOTING and MaintenanceTOP View Cable DiagramsLeg Press Cable Military Press Cable 72 and Leg Press CableExploded DRAWING-Model No. WESY39310 Page Page Part LIST-Model No. WESY39310 Exploded Drawing Icon Health & FITNESS, INC., 1500 S W., LOGAN, UT Ordering Replacement PartsLimited Warranty