Electrolux 1600 What to do if, Remedying a malfunction, FORCE! or an error code CD6 is shown

Page 42

What to do if...

Remedying a malfunction

In the event of a malfunction, try to rectify the problem yourself with the aid of the instructions provided here. If you request a visit from customer service to remedy one of the malfunctions listed here, or to rectify an error made when using the appliance, the customer service engineer’s visit will not be free of charge, even during the warranty pe- riod.

•If any of the following error messages are shown in the display, you may be able to rectify the malfunction yourself:

–ATTENTION / PLEASE CLOSE THE DOOR

–ATTENTION CD1 / PLEASE OPEN THE TAP

–ATTENTION CD2 / PLEASE CHECK THE WATER DRAINAGE

(To remedy the error, see the following malfunction chart.)

After you have rectified the error, press the START button. If the error code is displayed again, please contact customer service.

• If ATTENTION / PLEASE

 

 

 

 

 

 

 

ATTENTION

 

CALL YOUR LOCAL SERVICE

 

Cd6

 

FORCE! or an error code

 

 

 

 

 

 

 

 

(e.g. CD6) is shown in the

 

PNC: xxx xxx xxx

 

 

 

 

 

display, please proceed as

 

 

 

 

 

PLEASE CALL YOUR LOCAL

 

 

 

 

 

 

 

 

follows:

 

SERVICE FORCE

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

–Switch off the appliance and switch it on again

after approx. 3 seconds;

–Reset the wash programme again;

–Press the START button.

If the error code is displayed again, please contact customer service. In such an event, please provide the error code shown in the display and the PNC no. shown.

Problem

Possible cause

Remedy

 

The power plug is not

Connect the plug to a power

 

connected.

outlet.

The washing machine

A domestic fuse has tripped.

Replace the fuse.

does not work.

 

 

 

The START button has not

Press the START button.

 

been pressed.

 

 

 

 

 

42

Page 41 Page 43
Image 42
Page 41 Page 43
Contents ÖKO-LAVAMAT Following symbols are used in the text Dear CustomerContents Anti-flood Aqua Control + Aqua Alarm Changing the languageInstallation and connection instructions Safety Prior to initial start-upIntended Use Child Safety General SafetyEnvironmental tips When disposing of the washing machineDisposal PackagingTurn the appliance on by Possible languages will appear in the right of the displayDescription of appliance Front viewDrawer for detergent and conditioner Information panel Control panel with displayCancelling settings Main control featuresSwitching the appliance on and off Off. When the appliance isNavigation display Control knob and pagesButtons and levels Level OptionsFirst set the programme level 1, then the option level Setting a programme an example Level ExtrasTion has been activated Will appear in the symbol row Press the Start button. The wash programme will startWoollens H handwash Overview of functionsProgrammes Level Wash programmes Silk H handwashAn especially gentle wash programme which Special programmes40-60 MIX Cose, modal, cupro, lyocellOptions level Extras level Sensitive SMore water when rinsing Water is very soft, it canHowever be helpful to use Preparing for a wash cycle Sorting and preparing the washingTypes of washing and care symbols Quantities of detergent and conditioners? Water softeningWater hardness details Setting the time Before the first washCarrying out a wash programme prior to first use Performing a wash cycle Opening and closing the doorLoading the washing Adding detergents/conditioners Adding detergent/conditionerCompartment for liquid conditioners centre front Setting a wash programme If using liquid detergents/tabletsSet the options, e.g. Delay Start Delay Start option can be set at 30-minute inter- valsIf a delayed start has been set Starting a wash programmeMoisture/Loading Cancelling the programmeWash programme progress Changing the spin speedSpin When the wash programme is completeFor rinse hold Set the desired spin speedIf Overdosing is shown Overdosing indicatorUnloading the washing Amount of washing loaded the next time you washSaving a programme setting MemoryIf Memory is highlighted Press the Select button Cancelling a saved programme setting Changing the language Select English Back DEUTSCH§ ITALIANO§ FRANÇAIS§ Extras Maintenance and Cleaning Control panelDetergent Dispenser Drawer Washing Machine Drum Maintenance WashTo run a maintenance wash Main doorRemedying a malfunction FORCE! or an error code CD6 is shownWhat to do if FollowsStart button was Screw the inlet hose Tion CD 1 / Please Outlet hose is kinked Straighten the hose Washing has not If after the last rinse foam is still visible If the washing results are not satisfactoryIf there are still grey stains on the washing If there are white residues on the washingCarrying out an emergency emptying When the water is completely drained Drain pumpWhat does Update mean? Close the flapChild Safety Feature Setting the child safety featureCancelling the child safety feature Consumption values and load sizes Consumption valuesLoad sizes Wash programme Type of fabric Load size in kg1Installation and connection instructions Installation Safety PrecautionsTransporting the appliance Installation of the applianceWhen transporting the unit with a sack trolley Remove transport packagingPage Installation-Site preparation Installation on a concrete baseInstallation on a Suspended Floor Levelling the applianceElectrical Connection Brown LivePermanent Connection Water connection Water pressureInlet Hose Connection Water Drainage Pump head of greater than 1m Height Adjustment Approx. +10 / -5mm Technical dataDimensions Dimensions in mmWarranty conditions Great BritainPage Page Page Index 0870 5 929 Customer CareAEG Hausgeräte GmbH Postfach 90327 Nürnberg Copyright by AEG
Top Page Image Contents