JVC LVT0858-001A manual Setting the Speakers, Information

“YES” for the subwoofer and “SML” for the front, center and rear speakers are initial settings. To get best possible sound, change the subwoofer and speaker settings to fit your listening conditions.

Setting the Subwoofer Information	Remote
	NOT

Register whether you have connected a subwoofer or not. If you have already connected a subwoofer, follow the procedure below.

Before you start, remember...

There is a time limit in doing the following steps. If the setting is canceled before you finish, start from step 1 again.

1Press SETTING.

SETTING	The CONTROL buttons now work for basic
	settings.

1Press SETTING.

SETTING The CONTROL buttons now work for basic

settings.

2Press CONTROL ∞ (or 5) repeatedly until one of the following speakers (with the current

setting)* appears.

CONTROL
ANALOG	L	C	R	PR ΙΙ
LPCM	SUBWFR LFE DSP
DOLBY D	LS	S	RS	AUTO SR	VOL
DTS				INPUT ATT

Basic Settings

2Press CONTROL ∞ (or 5) repeatedly until “SUBWFR (Subwoofer)” (with the current

setting)* appears on the display.

CONTROL

RΙΙ

SR
ATT	VOL

FRNT SP (Front Speaker) : To register the front speaker size.

CNTR SP (Center Speaker): To register the center speaker size.

REAR SP (Rear Speaker) : To register the rear speaker size.

*“SML (small)” is the initial setting. If you have already changed the setting, another size will be shown.

* “YES” is the initial setting. If you have already changed the	3 Press CONTROL 3 (or 2) to select the
setting, “NO” will be shown.
	appropriate speaker size.
3 Press CONTROL 3 (or 2) to select “YES.”
	• Each time you press the button, the speaker size changes as
	follows:
• Each time you press the button, the subwoofer setting
alternates between “YES” and “NO.”	CONTROL
CONTROL

ANALOG	L	C	R	PR ΙΙ		ANALOG	L	C	R	PR ΙΙ
						LPCM	SUBWFR LFE DSP
LPCM	SUBWFR LFE DSP
						DOLBY D	LS	S	RS	AUTO SR
DOLBY D	LS	S	RS	AUTO SR	VOL	DTS				INPUT ATT	VOL
DTS				INPUT ATT

YES : Select this when you have connected a subwoofer. The subwoofer speaker indicator ( SUBWFR ) lights up on the display (see page 11). You can adjust the subwoofer output level (see page 22).

NO : Select this when you have not connected or have disconnected a subwoofer.

Setting the Speakers	Remote
Information	NOT

To obtain the best possible effect from the Surround modes (see page 32), register the following information after all connections are completed.

•Speaker Size—FRNT SP, CNTR SP, REAR SP

•Speaker Distance—FRNT D, CNTR D, REAR D

•Crossover Frequency—CROSS

•Low Frequency Effect Attenuator—LFE

•Dynamic Range Compression—D.COMP

Speaker Size—FRNT SP, CNTR SP, REAR SP

Register the sizes of all the connected speakers.

•When you change your speakers, register the information about the speakers again.

Before you start, remember...

There is a time limit in doing the following steps. If the setting is canceled before you finish, start from step 1 again.

Ex.: When registering the rear speaker size.

LRG (Large)	: Select this when the speaker size is relatively
	large. (See “Notes” below.)
SML (Small)	: Select this when the speaker size is relatively
	small. (See “Notes” below.)
NO	: Select this when you have not connected a
	speaker. (Not selectable for the front speakers.)

4Repeat steps 2 and 3 to select the appropriate size for the other speakers.

Notes:

•Use the following criteria as reference when adjusting:

–If the size of the cone speaker unit built in your speaker is greater than 12 cm, select “LRG (large),” and if it is smaller than 12 cm, select “SML (small).”

•If you have selected “NO” for the subwoofer, you can only select “LRG (large)” for the front speaker size.

•If you have selected “SML (small)” for the front speaker size, you cannot select “LRG (large)” for the center and rear speaker sizes.

15