JVC LVT0858-001A Troubleshooting, Operations, Problem Possible Cause Solution, To be on the Next

Page 47

Troubleshooting

Use this chart to help you solve daily operational problems. If there are any problems you cannot solve, contact your JVC’s service center.

PROBLEM

POSSIBLE CAUSE

SOLUTION

 

 

 

 

The power does not come on.

The power cord is not plugged in.

Plug the power cord into an AC outlet.

 

 

 

No sound from speakers.

Speaker signal cables are not

Check speaker wiring and reconnect if

 

connected.

necessary.

 

 

 

 

 

 

An incorrect source is selected.

Select the correct source.

 

 

 

 

 

Muting is activated.

Press MUTING to cancel the mute.

 

 

 

 

An incorrect input mode (analogue or

Select the correct input mode (analogue or

 

digital) is selected.

digital).

 

 

 

 

 

 

Connections are incorrect.

Check connections.

 

 

 

 

 

TV Direct is activated.

Deactivate TV Direct (see pages 11 and 19).

 

 

 

Buttons cannot be used.

TV Direct is activated.

Deactivate TV Direct (see pages 11 and 19).

 

 

 

Sound from one speaker only.

The balance is set to one extreme.

Adjust the balance properly (see page 20).

 

 

 

Continuous hiss or buzzing during FM

Incoming signal is too weak.

Connect an outdoor FM antenna or contact

reception.

 

your dealer.

 

 

 

 

 

 

The station is too far away.

Select a new station.

 

 

 

 

 

An incorrect antenna is used.

Check with your dealer to be sure you have a

 

 

correct antenna.

 

 

 

 

 

 

Antennas are not connected properly.

Check connections.

 

 

 

 

Occasional cracking noise during FM

Ignition noise from automobiles.

Move the antenna farther from automobile

reception.

 

traffic.

 

 

 

 

 

“OVERLOAD” starts flashing on the

Speakers are overloaded because of

1. Press STANDBY/ON

on the front

display.

high volume.

panel to turn off the unit.

 

 

 

2. Stop the playback source.

 

 

 

3. Turn on the unit again, and adjust the

 

 

volume.

 

Mastering Remote

Operations /

Troubleshooting

Speakers are overloaded because of short circuit of speaker terminals.

Press STANDBY/ON on the front panel to turn off the unit, then check the speaker wiring.

If “OVERLOAD” does not disappear, unplug the AC power cord, then plug it back again.

If speaker wiring is not short-circuited, contact your dealer.

TO BE CONTINUED ON THE NEXT PAGE

43

Page 46 Page 48
Image 47
Page 46 Page 48
Contents RX-E111RSL / RX-E112RSL If in Doubt Consult a Competent Electrician RX-E111RSL RX-E112RSL Above ALL Table of Contents Front Panel Remote ControlParts Identification 7 8 9 pGetting Started Before Installation Putting Batteries in the Remote ControlChecking the Supplied Accessories Antenna Connecting the FM and AM MW/LW AntennasGetting Started FM Antenna suppliedAM MW/LW antenna connection Connecting the SpeakersConnecting the front, center, and rear speakers Connecting the subwoofer speakerRX-E111R RX-E112R Speaker Layout DiagramConnections Connecting Audio/Video ComponentsDigital connections AnalogueRGB Audio OUT VCR STB DVD AudioVideo VideoConnecting the Power Cord Select the Source to Play Turn On the PowerAdjust the Volume Basic OperationsPress TV Direct Basic adjustment of auto memorySignal and speaker indicators on the display Activating TV DirectChanging the Display Brightness Basic OperationsTurning Off the Sounds Temporarily-MutingDigital in Terminals Basic SettingsSetting the Digital Input Selecting the Analogue or Digital Input Mode∞/ 3/ 2 Display Basic SettingsSetting Input ANALOG/DIGITAL ControlInformation Setting the SpeakersSpeaker Distance-FRNT D, Cntr D, Rear D Current setting* appears on the displayPress Control ∞ or 5 repeatedly until Press Control 3 or 2 to select the distanceDynamic Range Compression-D.COMP Press Control 3 or 2 to select the LFE attenuator levelCrossover Frequency-CROSS Low Frequency Effect Attenuator-LFEDisplay Press Control 3 or 2 to select on orOFF ∞ /3 /2Repeat steps 1 and 2, then select OFF in step Setting the Auto Function ModeTo cancel Auto Surround Press Control 3 or 2 to select AUTO1 or AUTO2Press Adjust Sound AdjustmentsPress Control 3 or 2 to adjust the front speaker balance Adjusting the Front SpeakersReinforcing the Bass Adjusting the ToneAdjustments Sound AdjustmentsAdjusting the Subwoofer Output Level Press Control 3 or 2 to adjust the sound Output levelPress FM/AM to select the band Tuning into Stations ManuallyEx. When selecting the FM band Tuner OperationsPress Memory Using Preset TuningTo erase a stored preset station Tuner OperationsChannel number you want Selecting the FM Reception ModeTo tune in a preset station To restore the stereo effectFM Stations Using the RDS Radio DataWhat information can RDS signals provide? System to ReceiveOn the display, while PTY Select is flashing Set RDS/DVD Menu selector to RDS. RDSPress PTY Search while listening To an FM station Press PTY 9 or PTY until PTY code you want appearsJazz music Description of the PTY codesPress TA/NEWS/INFO repeatedly Switching to BroadcastProgram Your Choice TemporarilyTypical Multichannel 5.1-channel reproduction Creating Realistic Sound FieldsDolby Surround DTS Digital SurroundHall DAP Digital Acoustic Processor modes All Channel StereoAll Channel Stereo reproduction Creating sound fieldSelecting the Surround modes Creating Realistic Sound FieldsAbout Relations between Speaker Layout and Surround Modes Turning on or off the Surround modesPress Test to check the speaker output balance Surround modeExcept for the digital multichannel PL II Music according to a playing sourcePress Sound Adjust the following speaker output levels from -10 to +10To cancel Surround Mode Press Test again to stop the test toneOnly for ALL CH ST. to adjust the center speaker level Using DAP Modes and All Channel Stereo Remote ControlAdjust the rear speaker output levels from -10 to +10 To cancel DAP Modes and All Channel StereoPanorama control ON/OFF ModeRepeat steps 5 and 6 to make other adjustments Press Control 3 or 2 to make adjustmentsRepeat steps 5 and 6 to adjust the other settings Using DAP Modes and All Channel Stereo Front PanelReinforcing the Bass-BASS Boost button Turning on the power-POWER buttonsAdjusting the volume-VOLUME buttons Mastering Remote OperationsSelecting the channels-10 keys Adjusting the sound and operating tuner -10 keysOperating RDS These buttons work only for TV operations Mastering Remote OperationsOperating DVD menu for JVC’s DVD player Manufacturers’ codes for STB Codes Try to operate your DVD player by pressingManufacturers’ codes for DVD player Codes Try to operate your STB by pressing STBTry to operate your TV by pressing TV If there are more than one code listed for your brand of TVManufacturers’ codes for VCR Codes CGMTo be on the Next TroubleshootingProblem Possible Cause Solution OperationsTroubleshooting Amplifier SpecificationsAM MW/LW tuner SpecificationsTuning Range KHz to FM tuner IHF0102NHMMDWJEIN

LVT0858-001A specifications

The JVC LVT0858-001A is a versatile and well-engineered speaker system designed for optimal audio performance and user satisfaction. Built with high-quality materials and advanced technologies, this speaker is perfect for enhancing the sound quality of your home entertainment setup.

One of the main features of the LVT0858-001A is its impressive sound output. The speaker is equipped with a robust driver that delivers clear and powerful audio across a wide frequency range. This allows listeners to experience the intricacies of their favorite music, movies, and games with exceptional clarity and depth. The precise engineering of the speaker ensures minimal distortion, allowing for an immersive listening experience.

The design of the JVC LVT0858-001A is sleek and modern, making it an attractive addition to any room. Its compact form factor allows it to fit seamlessly into various environments, whether placed on a shelf, mounted on the wall, or paired with a home theater system. The speaker's aesthetic, combined with its performance, makes it suitable for diverse applications, from casual listening to serious audiophile setups.

One of the standout technologies featured in the LVT0858-001A is its enhanced bass response. The speaker is designed with a dedicated subwoofer that deepens low-frequency sounds, ensuring that users can feel the pulse of the music or the rumble of action in films. This technology not only adds to the overall audio experience but also highlights the subtlety in soundtracks that might otherwise go unnoticed.

Additionally, the JVC LVT0858-001A is compatible with a variety of audio sources. Whether connecting through Bluetooth, HDMI, or traditional wired options, users can easily integrate the speaker into their existing audio systems. This flexibility enhances its functionality, making it a great choice for both casual users and audio enthusiasts alike.

In conclusion, the JVC LVT0858-001A speaker system combines advanced technologies, a sleek design, and exceptional sound quality. With features aimed at delivering an immersive audio experience, it stands out as a reliable option for anyone looking to elevate their sound experience. Whether for music, movies, or gaming, this speaker is engineered to satisfy even the most discerning listeners.
Top Page Image Contents