Miele T 8822 C Rear view, Installation site, Transporting the dryer to its installation site

Page 42

Installation

Rear view

Protruding lid for holding when moving the dryer (see arrows)

Air inlet vent for cooling the condenser unit

Mains connection cable

Hose for external drainage of condensed water

Accessories for connection to a sink drain outlet

Installation site

Make sure the dryer door can be opened without hindrance after in- stallation.

Transporting the dryer to its installation site

When moving the dryer, hold it by the lid where it protrudes to the rear. To manoeuvre the dryer out of its packing case to its installation site hold it by the front feet and the base of the lid.

Building under a continous worktop / in a kitchen run

A building-under kit* with a coverplate to replace the appliance lid is required. It must be fitted by a suitably qualified person to ensure electrical safety.

N.B. If you wish to push your appliance under a worktop and there is space to do this without removing the lid the building-under kit is not necessary. Otherwise it is essential.

–The building-under kit is supplied with its own installation instructions.

–N.B. When built-under drying times may be longer.

–The electrical socket must be located in an accessible position near the appliance.

With niche heights of:

–830-840 mm, longer screw feet* are required.

–870-885 / 915-930 mm, one or two raising kits* are required.

* Miele accessory available to order

Replacing the lid

If the lid has been removed in order to fit a coverplate, ensure that, if the lid is ever replaced, it fits securely into the rear holders. Otherwise, it is not properly secure for transport.

42

Image 42

Contents Operating instructions For condenser tumble dryer T 8822 C Disposal of your old appliance Caring for the environmentDisposal of the packing material Energy saving tipsContents Contents Consumption data Technical data Correct application Safety with children Technical safety Page Correct use Page Page Accessories Operating the tumble dryer Control panelProgramme duration / Estimated time remaining Display showsFollowing are also selected via the display Drying Garment care label symbolsTips on drying IroningSort the laundry How to dry correctlyBrief instructions Turn on the tumble dryerSelect any Extra options / Delay start Select a programmeDrying level programmes Start the programme Before the end of a programmeRemove the laundry at the end of the programme Extra options / Delay start Delay startExtra options Minimum iron Max. load 3.5 kg Normal, Hand iron Cottons Max. load 7 kg Extra dry, NormalHand iron, Machine iron Delicates Max. load 2.5 kg Normal, Hand ironProgramme chart Warm air Max. load 7 kg Shirts Max. load 2 kg Normal, Hand ironCool air Max. load 7 kg Gentle smoothing Max. load 1 kgOnce a programme has started Altering Delay startChanging the programme sequence Adding or removing laundry after a programme has startedElectronic system lock To activate the lockTo deactivate the lock Cleaning and care Emptying the condensed water containerCleaning the fluff filters Cleaning them whilst dryCleaning them with water Cleaning the tumble dryer Cleaning the condenser unit Removing the condenser unitChecking the condenser unit Checking and cleaning the condenser unit housing Problem solving guide Check and fault messagesTo switch off this Problem Possible cause RemedyAirways indicator To switch off this warningFlashing slowly Problem Possible cause Remedy Start/Stop button isProgramme indicator Display is darkAn unsatisfactory drying result Even switches off Other problemsProblem Possible cause Remedy Drying process Goes on too long orPower cut Problem Possible cause Remedy Water leaks fromBeen cleaned Dryer after Changing the lamp Appliance guarantee After Sales serviceFuture updates PC Optional accessoriesInstallation Front viewRear view Installation siteTransporting the dryer to its installation site Replacing the lidRoom ventilation Before moving the tumble dryer again e.g. when moving houseLevelling the appliance Washer-dryer stackExternal condensed water outlet General notesArranging the drain hose Installation conditions requiring a non-return valve External drainage via a sink or gullyFit adapter 1 to the sink drain outlet Non-rewireable plugs BS Electrical connectionElectrical connection U.K Consumption data Woollens handcareTechnical data To check the setting Programmable functionsReduced residual moisture. Laundry drier Programmable functions Hours anti-crease factory default setting Anti-creaseAnti-crease off Hour anti-crease Altering the volume of the buzzer Normal buzzer Factory default setting Loud buzzerReduced residual moisture. Laundry drier Extending the cooling down time Cooling down time extended by ten minutesOff Factory default. Not in current pro- grammeStandby Follow the steps ,, ... to pro- gramme and store in memoryFactory default setting. Not in current programme Memory deactivated factory default setting Memory activated Memory functionClean out airways indicator Keypad tone Adjusting the dryers electronics for very soft water Factory default setting Adjusted for very soft waterExtending the range of the drying levels Page Alteration rights reserved/0113 Nr 847 520

Related manuals

Manual 56 pages 37.44 Kb