AEG L 75670 FL AT the END of the Programme, Change a Function, SET the Delay Start, Open the Door

Page 18

18

CHANGE A FUNCTION

You can change only some functions before they operate.

1.Press button 4 . The indicator flashes.

2.Change the function set.

SET THE DELAY START

1.Press button 5 again and again until the display shows the number of minutes or hours. The related symbols comes on.

2.Press button 4 , the appliance starts the countdown of the delay start.

When the countdown is comple- ted, the programme starts auto- matically.

Before you press button 4 to start the appliance, you can can- cel or change the set of the de- lay start.

You cannot set the delay start with the Steam programme.

CANCEL THE DELAY START

1.Press button 4 . The related indi- cator flashes.

2.Press button 5 again and again until the display shows 0’.

3.Press button 4 . The programme starts.

OPEN THE DOOR

While a programme or the delay start operates, the appliance door is locked.

To open the appliance door:

1.Press button 4 . The door lock symbol in the display goes off.

2.Open the appliance door.

3.Close the appliance door and press button 4 . The programme or the delay start continues.

If the temperature and level of the water in the drum are too high, the door lock symbol stays on and you cannot open the door. To open the door do the steps that follow:

1.Deactivate the appliance.

2.Wait for some minutes.

3.Make sure that no water is in the drum.

If you deactivate the appliance, it is necessary to set the pro- gramme again.

AT THE END OF THE PROGRAMME

The appliance stops automatically.

The acoustic signals operate.

In the display comes on.

The indicator of the Start/Pause but- ton 4 goes off.

The door lock symbol goes off.

Press button 1 to deactivate the ap- pliance. After five minutes from the end of the programme, the energy saving function automatically deacti- vates the appliance.

When you activate the appli- ance again, the display show the end of the last set programme. Turn the programme knob to set a new cycle.

Remove the laundry from the appli- ance. Make sure that the drum is empty.

Keep the door ajar, to prevent mil- dew and odours.

Close the water tap.

The washing programme is completed, but there is water in the drum:

The drum turns regularly to prevent the creases in the laundry.

The door stays locked.

You must drain the water to open the door.

Image 18
Contents FL L 75470 FL L 75670 FL Contents ServiceAccessories and Consumables For Perfect ResultsVisit OUR Website for General Safety Safety InformationChild Safety Device Care and CleaningWater connection Discard the ApplianceEcological Hints Environment ConcernsPackaging Materials Interest of the EnvironmentTechnical Information IPX4Accessories Product DescriptionProgramme Knob Control PanelON/OFF Button DisplayDelay Start Button Time Save ButtonExtra Rinse Button Temperature ButtonAcoustic Signals Function Stain ButtonProgrammes Extra RINSE4 Consumption Values Programme Energy consumption Water consumpUsing the Appliance Before First USELoading the Laundry Filling the Detergent and Additives Check the position of the flapSetting and Starting a Programme Cancel a ProgrammeInterrupt a Programme AT the END of the Programme SET the Delay StartCancel the Delay Start Change a FunctionEnglish Stubborn Stains Helpful Hints and TipsLaundry Load Detergents and AdditivesWater hardness Mmol/l Clarke Care and Cleaning Detergent Dispenser Drain PumpPage Inlet Hose Filter Valve FilterEmergency Drain Frost Precautions Troubleshooting Problem Possible cause Possible solutionDelay start is set Problem Possible cause Possible solution Installation UnpackingPull out the plastic spacers Positioning and Levelling Installation on a not hard floor Inlet HoseWater-stop device Water DrainageEnglish 132939750-A-112011