AEG 86810 manual Safety information concerning installation, Installing the appliance

Page 34

Installation and connection instructions

1Safety information concerning installation

•This washing machine cannot be built-in.

•Before using for the first time, check the appliance for damage sus- tained while it was being transported. Do not under any circumstanc- es connect an appliance that is damaged to the mains. In the event of damage to the appliance contact your supplier.

•Be sure to remove all the components of the transport lock before us- ing the appliance for the first time. Otherwise when spinning damage may be caused to the appliance or to neighbouring units or furniture.

•Before using the appliance for the first time, splash protection must be completed. (See “Removing transit packaging”).

•Always plug the mains plug into a correctly installed shockproof socket.

•If hard-wired: hard-wiring to the mains may only be carried out by an a qualified electrician.

•Prior to using the appliance for the first time, ensure that the rated voltage and current on the rating plate match the mains voltage and current where the appliance is to be installed. The required fuse pro- tection is also to be found on the rating plate.

•If work on the plumbing is required for the proper connection of the washing machine to the water supply, this must be undertaken by a registered plumber.

•If work on the electricity supply system is required for the proper connection of the washing machine to the electricity supply, this must be undertaken by a registered electrician.

•The washing machine’s mains cable must only be replaced by a Service Force Engineer

Installing the appliance

Transporting the appliance

1Warning: The washing machine is very heavy. There is a risk of injury. Exercise care when lifting the appliance.

34

Image 34

Contents Lavamat Following symbols are used in the text Dear CustomerContents Installation and connection instructions Safety information concerning installationChild safety SafetyPrior to using the appliance for the first time General safetyResulting overheating may constitute a fire hazard What is shown in the display Cycle end atProgram overview Easy IronUse/Features Care Symbols1 R a c h e Prior to using for the first timeN g u a g e Programmende umCarrying out a wash programme prior to first use Setting the timePreparing and sorting washing Preparing washingOpening the door/Loading the washing Running a wash cycleAdding detergent/conditioner If you are using liquid detergent Switching on the appliance/selecting a programmeWashing powder/tablets for the main wash cycle Speed or Rinse Hold is displayed Changing spin speed/selecting rinse holdWith spin speed 0 the TEMP. RPM Options OK Time Setting options SetupSensitive To switch off the optionPrewashing Prewash, Sensitive, Stain, Night CycleTime saving Setting timesDelay Start Time Saving Short or Very ShortStart Delay StartStart in 4h Press the OK key. Start in 0 min is shown in the displayProgramme progress WashingStarting a programme Interrupting a programme/Adding washingWashing cycle complete/Removing the washing SetupIf Rinse Hold or Night Cycle was selected Memory 1, 2 Setting the MemoryMemory Store program Changing the MemoryN s e + U n dExtra Rinse Language Set timeClock Contrast and brightness Child safety deviceDesired setting. With Each press of the key or ifDeactivating the child safety device Cleaning and maintenanceCleaning procedure Detergent dispenser drawerDoor and rubber collar Clean the glass in the door and the rubber collar regularlyWashing drum Top of the washing-in chamber, with a brushWhat to do if Remedying small malfunctionsAdjusted Foam can still be seen following the final rinse If the wash result is not satisfactoryThere are grey stains on the washing There are white residues on the washingWhen the water has all drained away Carrying out an emergency drainDrain pump Packaging material DisposalOld appliance Technical data Consumption valuesTransporting the appliance Safety information concerning installationInstalling the appliance This washing machine cannot be built-inUnpacking When using a sack trolley to transport the washing machineRemove the power supply cable Only use the sack trolley on the side of the appliancePage Where to install Electrical Connection Making the appliance levelBrown Live Wire coloured green and yellow Permanent ConnectionWater inlet Connecting to the water supplyPermitted water pressure Open the porthole and extract the inlet hoseWater Drainage Pumping heights of over 1 metre For drainage into an outletGuarantee/Customer Service Great BritainEuropean Guarantee LU4 9QQ Slovenija For general enquiries concerning 0870 5 929Customer Care Major Appliances132 977 Subject to change without notice