Smeg TLS12 manual Indication on Description

Page 16

 

Indication on

 

Description

 

 

Red indication lamp

time display

 

 

 

 

Causes

 

 

lights up

(if fitted on your

 

 

 

 

Solutions

 

 

 

machine)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

“bdd”

Appliance stops during the programme.

 

 

(in case your washing

 

 

 

 

 

 

machine has no

“Drum flaps open” (the drum flaps have not been

 

 

display: all lamps of the

closed properly).

 

 

 

 

 

programme sequence

Push the “Reset” button

for at least 3 seconds

 

 

indicator light up)

 

 

and wait until the “Door open”

lights up. Open

 

 

 

 

 

 

lid and close drum flaps, then select and start

 

 

 

desired programme again. If fault persists, notify our

 

 

After-Sales Service.

 

 

 

 

 

from “F02” to “F35”

“Electrical module fault”

 

 

 

 

(except “F09”)

Select and start “Drain” programme or push

 

 

 

“Reset” button

for at least 3 seconds.

 

 

“F09”

“Water level too high” (after programme

 

 

 

cancellation or false operating). Switch off appliance

 

 

and then switch it on again, select programme

 

 

 

“Drain” and start within 15 sec.

 

 

 

“FA”

“Waterstop fault”

 

 

 

 

“Service”

 

Switch off appliance, pull out mains plug and turn

 

 

 

water tap off. Tilt appliance forward carefully to

 

 

 

allow collected water to flow out from the bottom.

 

 

Then:

 

 

 

 

 

 

Plug in the appliance again.

 

 

 

 

Turn the water tap on (if water immediately flows

 

 

into the appliance without the appliance being

 

 

 

started, there is a failure; turn off the tap and notify

 

 

After-Sales Service).

 

 

 

 

 

Select and start the desired programme again.

 

 

“Fod”

“Overfoaming”

 

 

 

 

 

 

Too much foam interrupted the wash programme.

 

 

 

Select and start “Rinse & Spin” programme

.

 

 

Afterwards select and start desired programme

 

 

 

again, using less detergent.

 

 

 

 

If faults persist, unplug the appliance, turn off the

 

 

 

water tap and contact our After-Sales Service (see

 

 

 

next chapter).

 

 

 

 

 

 

 

 

 

 

 

If your washing machine has no time display, check which of the previously described situations could be the origin of the fault and follow the corresponding instructions.

GB 14

Image 16
Contents Contents Programme Chart Consumption Data Before Using the Washing Machine Precautions and General Recommendations Description of the Washing Machine Adjustable feetBefore the First Wash Cycle Preparation of the Washing Sort the laundryStain removal Dyeing and bleachingLoading the laundry Choice of the right detergents and additives Detergents and AdditivesDosage Using chlorine bleach Where to put detergents and additivesUsing starch powder Cleaning the FILTER/ Draining Residual Water Water inlet hose filter Detergent dispenserWater inlet hose Appliance exterior and control panel Appliance interiorLid seal Water inlet hosesProblem Causes, Solutions, Tips Contains residues from Blocked see Care and MaintenanceSpin cycle Installation Animation appears during such update periodsDescription of red indications Red indication lampDescription Start/Pause light flashesIndication on Description Specify Before contacting After-Sales ServiceWait for the water to cool so as to avoid any accidents Removal of transport bracket Connect the water inlet hose Adjust the feetMake sure there are no kinks in the hose Water stop anti-flooding system Connect the water drain hoseEarth symbol Brown Live LTo fit a new plug, proceed as follows Polarized Plugs e.g pin, 13 amp plug conforming to BS 1363A