Alliance Laundry Systems WF400, WF305, WF235, WF185, WF150 Maintenance instruction of the machine

Page 46

Maintenance instruction of the machine

7

WARNING

To reduce the risk of electric shock, disconnect this appliance from the power supply before attempting any user maintenance. Turning the controls to the OFF position does not disconnect this appliance from the power supply.

Before starting wiring or inspection, power must be switched OFF, check to make sure that the operation panel indicator is off.

Any person who is involved in wiring or inspection shall wait for at least 10 minutes after the power supply has been switched OFF and check that there is no residual voltage using a tester or the like. The capacitor of the inverter or the EMC filter is charged with a high voltage for some time after power OFF, and it is dangerous.

End of day

General maintenance

Periodical maintenance

Clean AC drive filter:

a.Snap off external plastic cover which contains filter.

b.Remove foam filter from cover.

c.Wash filter with warm water and allow to air dry. Filter can be vacuumed clean.

Clean the entire cabinet of the machine regularly and remove all traces of soap, etc....

Remove all detergent residue in the soap dispenser with hot water.

Clean the door gasket and remove all detergents and other products.

Shut off the main water, steam, and power connections at the end of each day. Do not change the setting of the water inlet taps on boiler fed machines once these have been installed.

It is recommended to leave the door and soap dispenser open after use, to ventilate the machine.

Check for proper door lock operation on a daily basis.

The V-belts of the motors should be retightened after two to three months when first used. This is necessary because these belts are subject to a one-time stretching when first used. If this is not done, the belt starts to slip after a few months and will break shortly afterwards.

Check the water inlet filters to make sure they are not blocked by calcification.

Check the drain valve for obstructions.

If a machine frequently skips the final spin, check whether the probe of the out of balance switch is still in the appropriate position, that is horizontally centered and vertically 1/3 from the bottom inside the window. (When the drum is empty).

Lubricate the bearings after every 200 hours of operation or replace the automatic lubricator annually.

46

Image 46
Contents Washer Extractors Page Contents Internal connections of the electrical heating  Page Model Numbers Build-upPage Safety and Environmental Informations SafetyEnvironmental Disposal of UnitExplanation of Safety Messages Important Safety Instructions Page Operator Safety Technical data and dimensions Technical data WF150, IWF150, IWF033, CWF033Dimensions WF150, IWF150, IWF033, CWF033 Technical data WF185, IWF185, IWF040, CWF185, CWF040 Dimensions WF185, IWF185, IWF040, CWF185, CWF040 Technical data WF235, IWF235, IWF055, CWF235, CWF055 Dimensions WF235, IWF235, IWF055, CWF235, CWF055 Technical data WF305, IWF305, IWF075, CWF305, CWF075 Dimensions WF305, IWF305, IWF075, CWF305, CWF075 Technical data WF400, IWF400, IWF090 Dimensions WF400, IWF400, IWF090 Anchoring on a metal base Installation and Connection InstructionsSurface Directly on the ground260 670 731 410 640 780 260 770 831 510 640 780 282 347 347 Water connection ModelWater drain Electrical Installation Important Do not use fuses in place of a circuit breakerGrounding Instructions Machine Power Cable Connections Main power connectionConnection label Page Boiler Fed/Steam Heat Electric Heat Electrical Specifications WF150, IWF150, IWF033, CWF033Alternative Electric Heat Options Liters / 40 pounds Liters / 55 pounds Liters / 75 pounds Electrical Specifications WF400, IWF400, IWF090 Liters / 90 poundsLiquid soap connection option Connection of the liquid soap hosesWith an external tension 24V DC See Label Label Steam connection With direct steam injection into the machine See TableTechnical remarks Internal connections of the electrical heatingMaintenance instruction of the machine End of day General maintenance Periodical maintenanceAnnual maintenance Nameplate Contact InformationNameplate Location Replacement Parts Repair and after-sales service