Appropriate installation location

•Place the machine on a rigid floor. Do not place it on a long pile rug or similar surfaces.

•Total weight of the washing machine and the dryer -with full load- when they are placed on top of each other reaches to approx. 180 kilograms. Place the product on a solid and flat floor that has sufficient load carrying capacity!

•Do not place the product on the power cable.

•Do not install the product at places where temperature may fall below 0ºC.

•Place the product at least 1 cm away from the edges of other furniture.

Removing packaging reinforcement

Tilt the machine backwards to remove the packaging reinforcement. Remove the packaging reinforcement by pulling the ribbon.

Removing the transportation locks A Do not remove the transportation locks before

taking out the packaging reinforcement.

A Remove the transportation safety bolts before operating the washing machine, otherwise, the product will be damaged.

1.Loosen all the bolts with a spanner until they rotate freely (C).

2.Remove transportation safety bolts by turning them gently.

3.Attach the plastic covers supplied in the User Manual bag into the holes on the rear panel.

(P)

C Keep the transportation safety bolts in a safe place to reuse when the washing machine needs to be moved again in the future.

C Never move the product without the transportation safety bolts properly fixed in place!

Connecting water supply

C The water supply pressure required to run the product is between 1 to 10 bars (0.1 – 10 MPa). It is necessary to have 10 – 80 liters of water flowing from the fully open tap in one minute to have your machine run smoothly. Attach a pressure reducing valve if water pressure is higher.

C If you are going to use the double water-inlet product as a single (cold) water-inlet unit, you must install the supplied stopper to the hot water valve before operating the product. (Applies for the products supplied with a blind stopper group.)

C If you want to use both water inlets of the product, connect the hot water hose after removing the stopper and gasket group from the hot water valve. (Applies for the products supplied with a blind stopper group.)

A Models with a single water inlet should not be connected to the hot water tap. In such a case the laundry will get damaged or the product

will switch to protection mode and will not operate.

A Do not use old or used water inlet hoses on the new product. It may cause stains on your laundry.

1.Connect the special hoses supplied with the product to the water inlets on the product. Red hose (left) (max. 90 ºC) is for hot water inlet, blue hose (right) (max. 25 ºC) is for cold water inlet.

A Ensure that the cold and hot water connections are made correctly when installing the product. Otherwise, your laundry will come out hot at the end of the washing process and wear out.

2.Tighten all hose nuts by hand. Never use a wrench when tightening the nuts.

3.Open the taps completely after making the hose connection to check for water leaks at the connection points. If any leaks occur, turn off the tap and remove the nut. Retighten the nut carefully after checking the seal. To prevent water leakages and damages caused by them, keep the taps closed when the machine is not in use.

Connecting to the drain

•The end of the drain hose must be directly

connected to the wastewater drain or to the washbasin.

A Your house will be flooded if the hose comes out of its housing during water discharge. Moreover, there is risk of scalding due to high washing temperatures! To prevent such situations and to ensure smooth water intake and discharge of the machine, fix the end of the discharge hose tightly so that it cannot come out.

•The hose should be attached to a height of at least 40 cm, and 100 cm at most.

•In case the hose is elevated after laying it on the floor level or close to the ground (less than

40 cm above the ground), water discharge becomes more difficult and the laundry may

WNF 8467 ACE 40, WNF 8427 ACE 40, WNF 8447 AE 40 specifications

Blomberg is well-known for producing high-quality home appliances, and their range of washing machines exemplifies this reputation. Among the notable models are the Blomberg WNF 8447 AE 40, WNF 8427 ACE 40, and WNF 8467 ACE 40, each crafted to deliver optimal performance, efficiency, and user-friendly features.

The WNF 8447 AE 40 stands out due to its advanced technology and innovative design. This model is equipped with a ProSmart Inverter Motor, which not only ensures energy efficiency but also significantly reduces noise levels during operation. With a capacity of 8 kg, it is suitable for medium-sized households, making washing laundry a seamless task. The WNF 8447 AE 40 also features a 1400 RPM spin speed, ensuring that clothes come out cleaner and with less residual moisture, reducing drying times. Additionally, the machine includes multiple washing programs tailored for various fabric types and dirt levels, offering versatility for all laundry needs.

The WNF 8427 ACE 40 shares many similarities with the WNF 8447 AE 40 but focuses more on compactness and efficiency. This model is designed to fit smaller spaces while still providing a reliable 7 kg capacity. With an A+++ energy rating, it ensures low energy consumption without compromising washing performance. The child lock feature adds an extra layer of safety, making it a great choice for families. Furthermore, the Quick Wash option allows users to clean lightly soiled garments in as little as 28 minutes, perfect for busy lifestyles.

On the other hand, the WNF 8467 ACE 40 is the premium option among these models, ideal for larger households with its 8 kg load capacity. This washing machine incorporates the latest in sensor technology to optimize water and energy use based on the load size. It also features a variety of allergy-friendly programs, making it suitable for sensitive skin. The SteamTechnology feature reduces wrinkles and sanitizes clothes, effectively eliminating allergens.

Overall, the Blomberg washing machines WNF 8447 AE 40, WNF 8427 ACE 40, and WNF 8467 ACE 40 exemplify the brand's commitment to quality, innovation, and user convenience. With their advanced features and energy-efficient designs, they make laundry day easier and more sustainable for households of all sizes. Whether it's superior cleaning capabilities, compact design, or added safety features, each model brings something unique to the table, enhancing the laundry experience.