JVC UX-H30, CA-UXH33, SP-UXH33 manual Specifications

Page 31

Specifications

Amplifier Output Power:

20 W (10 W + 10 W) at 4 (10% THD) Audio input sensitivity/Impedance (at 1 kHz)

AUX:

500 mV/48.75 k

Speakers/Impedance:

4

Tuner

FM tuning range: 87.50 MHz – 108.00 MHz

AM tuning range:

 

MW:

522 kHz – 1 629 kHz

CD player

Dynamic range:

85 dB

Signal-to-noise ratio:

90 dB

Wow and flutter:

Immeasurable

Cassette deck

Frequency response:

 

Normal (type I):

50 Hz – 15 000 Hz

Wow and flutter:

0.15% (WRMS)

Speaker

Speaker units:

 

Full range:

8.0 cm cone x 1

Impedance:

4

Dimensions (approx.):

 

135 mm x 203 mm x 190 mm (W/H/D)

Mass (approx.):

1.7 kg each

Supplied Accessories

See page 6.

General

Power requirement:

 

 

AC IN:

230 V

, 50 Hz

DC IN:

12 V, 4 A

 

Power consumption:

35 W (at operation)

 

 

3.0 W (on standby)

Dimensions (approx.):

 

412 mm x 208 mm x 275 mm (W/H/D)

Mass (approx.):

 

6.5 kg

Design and specifications are subject to change without notice.

28

Image 31
Contents Micro Component System Important for Laser Products UX-H35/UX-H33/UX-H30 Introduction PrecautionsAbout This Manual Contents Front view Location of the ButtonsMain Unit Top viewMain unit Display window Display windowTape Tuner AUX Remote ControlFM antenna Supplied AccessoriesConnecting Antennas Getting StartedTo connect an outdoor AM MW antenna Connecting SpeakersTurn the AM loop antenna until you have the best reception Release your finger from the clampTo connect an audio equipment Connecting Other EquipmentTo connect the AC power cord To remove the speaker grillesWhen using the unit in your car Putting the Batteries into the Remote ControlCommon Operations Setting the ClockReinforcing the Bass Sound Turning On the PowerAdjusting the Volume Adjusting the Tone Bass/TreblePresetting Stations Tuning in to a StationReceiving FM Stations with RDS Tuning in to a Preset StationPress PTY Search Changing the RDS InformationSearching for Programs by PTY Codes PTY Search Press Display orange-colored. DisplayWait for about 3 seconds after Specifying the data type Switching Temporarily to a Program Type of Your ChoicePress TA/NEWS/INFO until Data type you want Appears on the displayGeneral notes When playing a CD-R or CD-RWPlaying Back Discs Press 0 Open on the unitProgramming the Playing Order of the Tracks-Program Play Basic Disc OperationsPress Random To check the program contentsPlaying at Random-Random Play Repeating Tracks-Repeat PlayPut a cassette in with the exposed part of the tape down Playing Back TapesPlaying Back a Tape Press for cassette deck on the unitTo protect your recording To record on both sides-Reverse ModeRecording Recording on a TapeRepeat steps 2 and 3 to record other tracks you want Disc Direct RecordingOne Track Recording Press ONE TouchSet the off-time when you want the unit To turn off standby Using the TimersUsing Daily Timer and Recording Timer Set the on-time when you want the unit To turn onWith the source to play Adjust the clock if you needSelect the volume level To deactivate the timer temporarilyPress Sleep Using Snooze TimerUsing Sleep Timer How the Sleep Timer actually worksHandling discs MaintenanceCleaning the unit Handling cassette tapesAction TroubleshootingSymptom CauseTest function Alarm functionAdditional Information Description of the PTY codesSpecifications 0103MWMMDWJEM