| 7. Select LOAD SIZE |
|
| 9. Select options | ||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Select the load size setting most suitable for your load. Small will add a low amount of water for smaller loads and Super will add the most amount of water for large or bulky loads. Items need to move freely.
Select the desired cycle options. If you are using fabric softener, be sure to select one of the Fabric Softener Added options.
8. Select TEMPERATURE |
|
| 10. Press START/Pause/Unlock | ||||
|
|
| to begin wash cycle | ||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Once you select a cycle, select the desired wash temperature by turning the Temperature knob to the appropriate setting based on your load. All rinses are tap cold.
NOTE: Always read and follow fabric care label instructions to avoid damage to your garments.
Wash Temp | Suggested Fabrics | |
|
| |
Hot |
| |
Some cold water is added to save | Whites and pastels | |
energy. This will be cooler than | Durable garments | |
your hot water heater setting. | ||
Heavy soils | ||
| ||
|
| |
Warm |
| |
Some cold water will be added, so | Bright colors | |
this will be cooler than what your | Moderate to light soils | |
previous washer provided. | ||
| ||
|
| |
Cool |
| |
Warm water may be added to | Colors that bleed | |
assist in soil removal and to help | or fade | |
dissolve detergents. | Light soils | |
|
| |
Cold |
| |
This is the temperature from your | Dark colors that | |
faucet. If your tap cold water is | bleed or fade | |
very cold, warm water may be | Light soils | |
added to assist in soil removal and |
| |
help dissolve detergent. |
| |
|
|
Press the START/Pause/Unlock button to start the wash cycle. Filling is delayed for several minutes while load balance is sensed. When the cycle has finished, the DONE indicator will light. Promptly remove garments after cycle has completed to avoid odor, reduce wrinkling, and rusting of metal hooks, zippers, and snaps.
Unlocking the lid to add garments
If you need to open the lid to add 1 or 2 missed garments:
Press START/Pause/Unlock; the lid will unlock once the washer movement has stopped. This may take several minutes if the load was spinning at high speed. Then close lid and press START/Pause/Unlock again to restart the cycle.
If lid is left open for more than 10 minutes, the water will pump out automatically.
Delay in water fill
Filling is delayed for 2 to 3 minutes to check for load unbalance. You will hear the hum of the spin prior to filling. This is normal operation.
WASHER MAINTENANCE
WATER INLET HOSES
Replace inlet hoses after 5 years of use to reduce the risk of hose failure. Periodically inspect and replace inlet hoses if bulges, kinks, cuts, wear, or leaks are found.
When replacing your inlet hoses, mark the date of replacement on the label with a permanent marker.
NOTE: This washer does not include inlet hoses. See the “Installation Instructions” for more information.
8