Washer Care, CleaningYourWasher | Whirlpool W10063560 guide

WASHER CARE

CleaningYourWasher

Cleaning the Door Seal/Bellow

1.Open the washer door and remove any clothing or items from the washer.

2.Inspect the gray colored seal/bellow between the door opening and the basket for stained areas. Pull back the seal/ bellow to inspect all areas under the seal/bellow and to check for foreign objects.

A.Seal/Bellow

3.If stained areas are found, wipe down these areas of the seal/ bellow, using the procedure that follows.

a)Mix a dilute solution, using ³₄ cup (177 mL) of liquid chlorine bleach, and 1 gal. (3.8 L) of warm tap water.

b)Wipe the seal/bellow area with the dilute solution, using a damp cloth.

c)Let stand 5 minutes.

d)Wipe down area thoroughly with a dry cloth and let the washer interior air dry with door open.

IMPORTANT:

■Wear rubber gloves when cleaning for prolonged periods.

■Refer to the bleach manufacturer’s instructions for proper use.

Washer Maintenance Procedure

This washer has a special cycle that uses higher water volumes in combination with liquid chlorine bleach to thoroughly clean the inside of the washer.

NOTES:

■Read these instructions completely before beginning the cleaning process.

■If necessary, the cleaning cycle may be interrupted by pressing the PAUSE/CANCEL button. This will stop the cycle. A RINSE/SPIN cycle must then be run to thoroughly rinse the remaining bleach from the washer. Failure to do so will cause damage to the washer and clothing added to the next cycle.

Begin procedure

1.Open the washer door and remove any clothing or items from the washer.

2.Be sure the door is closed.

3.Open the dispenser drawer and immediately add ²⁄₃ cup

(160 mL) of liquid chlorine bleach to the bleach compartment.

NOTE: Do not add any detergent to this cycle. Use of more than ²⁄₃ cup (160 mL) of bleach will cause product damage over time.

4.Be sure the dispenser drawer is closed.

5.Select the CLEAN WASHER cycle.

6.Press START.

NOTE: The basket will rotate, then the door will unlock, lock again, and then the cycle will continue.

■The machine will not fill, but the basket will rotate while the washer runs a short sensing cycle. This will take approximately 3 minutes.

7.The cycle will determine whether clothing or other items are in the washer.

a)If no items are detected in the washer, it will proceed to Step 8.

b)If any items are detected in the washer, all the Cycle lights will flash, “rL” or “F-34” will be displayed, and the Soak and Cycle Complete status lights will remain lit. Then the door will unlock.

■Press PAUSE/CANCEL to cancel the failure code. Then repeat steps 1, 2 and 6 to start the cycle again.

8.Once the cycle has begun, allow the cycle to complete.

9.After the cycle is complete, leave the door open slightly, to allow for better ventilation and drying of washer interior.

Always do the following to maintain washer freshness

■Use only HE High Efficiency detergent.

■Leave the door slightly open after each cycle to allow for better ventilation and drying of washer interior.

■Repeat the cleaning procedure monthly, using ²⁄₃ cup (160 mL) of liquid chlorine bleach.

■If the procedure does not sufficiently improve the machine freshness, please evaluate your installation and usage conditions for other causes.

Cleaning the exterior

Use a soft damp cloth or sponge to wipe up any spills. Occasionally wipe the outside of your washer to keep it looking new. Use mild soap and water. Do not use abrasive products.

W10063560 specifications

The Whirlpool W10063560 is a highly efficient refrigerator water filter designed to enhance the quality of drinking water by reducing contaminants and ensuring a consistent supply of clean water for your family. This advanced filter is compatible with a range of Whirlpool refrigerator models, making it a versatile choice for many households.

One of the main features of the W10063560 is its ability to reduce harmful substances such as chlorine, lead, and particulates, providing you with fresher and better-tasting water. By effectively filtering out these impurities, it not only improves the taste and odor of your water but also promotes a healthier lifestyle by reducing the potential for exposure to harmful chemicals.

The installation of the W10063560 filter is straightforward, allowing users to easily replace the old filter without the need for specialized tools. The filter typically needs to be replaced every six months, depending on water quality and usage, ensuring that you always have access to purified water. An indicator light on the refrigerator may alert you when it’s time for a replacement, making maintenance hassle-free.

In addition to its filtration capabilities, the W10063560 incorporates advanced technologies that enhance its performance. The filter features a high-grade carbon block, which effectively captures small particles and impurities. This technology ensures that the water flows effortlessly while maintaining high filtration efficiency, enabling consumers to enjoy clean water without compromising water pressure.

Another characteristic of this filter is its exceptional size compatibility, which fits various Whirlpool refrigerator models equipped with a filtered water dispenser. Its compact design ensures that it does not take up unnecessary space, allowing for a seamless integration into your refrigerator’s existing configuration.

This water filter also meets stringent industry standards, making it a reliable option for ensuring safe drinking water for your family. It has been tested and certified to the standards set forth by the NSF International, verifying its effectiveness in removing certain contaminants from drinking water.

In summary, the Whirlpool W10063560 water filter is an essential accessory for any Whirlpool refrigerator, promoting the health and well-being of families by delivering clean, refreshing water. With its ease of installation, advanced filtration technologies, and compatibility with various refrigerator models, it stands out as a top choice for consumers looking to improve their water quality.