Installation Instructions

RemoveTransportSystem

WARNING

Excessive Weight Hazard

Use two or more people to move and install washer. Failure to do so can result in back or other injury.

IMPORTANT: Position the washer so that the rear of the washer is within approximately 3 ft (90 cm) of its final location.

There are 4 blue bolts in the rear panel of the washer that support the suspension system during transportation. These bolts also retain the power cord inside the washer until the bolts are removed.

1.Using a 13 mm wrench, loosen each of the bolts.

2.Once the bolt is loose, move it to the center of the hole and completely pull out the bolt, including the plastic spacer covering the bolt.

3.Once all 4 bolts are removed, discard the bolts and spacers. Then pull the power cord through the opening of the rear panel and close the hole with the attached cap.

4.Close the bolt holes with the 4 transport bolt hole plugs.

NOTE: If the washer is to be transported at a later date, call your local service center. To avoid suspension and structural damage, your machine must be properly set up for relocation by a certified technician.

ConnecttheInletHoses

Insert new flat washers (supplied) into each end of the inlet hoses. Firmly seat the washers in the couplings.

A.Coupling

B.Washer

Connect the inlet hoses to the water faucets

Make sure the washer drum is empty.

1.Attach a hose to the hot water faucet. Screw on coupling by hand until it is seated on the washer.

2.Attach a hose to the cold water faucet. Screw on coupling by hand until it is seated on the washer.

3.Using pliers, tighten the couplings with an additional two-thirds turn.

NOTE: Do not overtighten or use tape or sealants on the valve. Damage to the valves can result.

Clear the water lines

■Run water through both faucets and inlet hoses, into a laundry tub, drainpipe or bucket, to get rid of particles in the water lines that might clog the inlet valve screens.

■Check the temperature of the water to make sure that the hot water hose is connected to the hot water faucet and that the cold water hose is connected to the cold water faucet.

W10063560 specifications

The Whirlpool W10063560 is a highly efficient refrigerator water filter designed to enhance the quality of drinking water by reducing contaminants and ensuring a consistent supply of clean water for your family. This advanced filter is compatible with a range of Whirlpool refrigerator models, making it a versatile choice for many households.

One of the main features of the W10063560 is its ability to reduce harmful substances such as chlorine, lead, and particulates, providing you with fresher and better-tasting water. By effectively filtering out these impurities, it not only improves the taste and odor of your water but also promotes a healthier lifestyle by reducing the potential for exposure to harmful chemicals.

The installation of the W10063560 filter is straightforward, allowing users to easily replace the old filter without the need for specialized tools. The filter typically needs to be replaced every six months, depending on water quality and usage, ensuring that you always have access to purified water. An indicator light on the refrigerator may alert you when it’s time for a replacement, making maintenance hassle-free.

In addition to its filtration capabilities, the W10063560 incorporates advanced technologies that enhance its performance. The filter features a high-grade carbon block, which effectively captures small particles and impurities. This technology ensures that the water flows effortlessly while maintaining high filtration efficiency, enabling consumers to enjoy clean water without compromising water pressure.

Another characteristic of this filter is its exceptional size compatibility, which fits various Whirlpool refrigerator models equipped with a filtered water dispenser. Its compact design ensures that it does not take up unnecessary space, allowing for a seamless integration into your refrigerator’s existing configuration.

This water filter also meets stringent industry standards, making it a reliable option for ensuring safe drinking water for your family. It has been tested and certified to the standards set forth by the NSF International, verifying its effectiveness in removing certain contaminants from drinking water.

In summary, the Whirlpool W10063560 water filter is an essential accessory for any Whirlpool refrigerator, promoting the health and well-being of families by delivering clean, refreshing water. With its ease of installation, advanced filtration technologies, and compatibility with various refrigerator models, it stands out as a top choice for consumers looking to improve their water quality.