Electrolux 1271 VI manual Positioning, Levelling, Set the machine, Carefully level by screwing

Page 51

Installation

Set the machine

upright and remove the two remaining bolts

from the back.

Pull out the three

plastic spacers from the holes into which the bolts were fitted.

Plug the open holes with the plugs which you will find in the plastic bag containing the instruction booklet.

You are advised to keep all transit devices so that they can be refitted if the machine ever has to be transported again.

Positioning

Install the machine on a flat hard floor.

Make sure that air circulation around the machine is not impeded by carpets, rugs etc.

•Before placing it on small tiles, apply a rubber coating.

•Never try to correct any unevenness in the floor by putting pieces of wood, cardboard or similar materials under the machine.

•If it is impossible to avoid positioning the machine next to a gas cooker or coal-burning stove, an insulating panel (85x57 cm) covered with aluminium foil on the side facing the cooker or stove, must be inserted between the two appliances;

•The machine must not be installed in rooms where the temperature can drop below 0.

•The water inlet hose and the drain hose must not be kinked.

•Please ensure that when the appliance is installed, it is easily accessi- ble for the engineer in the event of a breakdown.

Levelling

Carefully level by screwing the

adjustable feet in or out. Never place cardboard, wood or similar

materials under the machine to compensate for

any unevenness in the floor.

After having levelled the machine, tighten the lock nuts.

51

Image 51

Contents ÖKO-LAVAMAT 1271 VI Turbo Dear customer Contents Programme charts Bulding-in Technical data Service & Spare Parts Guarantee ConditionsSafety instructions General safetyInstallation During use Child safetyDisposal Packaging materialsMachine Tips for environmental protection Main features of your washer-dryer Front view Description of the applianceProgramme selector dial Control panelSTART/PAUSE button Delay Start buttonON/OFF button Mains-on lightProgramme Option buttons Drying Time buttonPrewash Programme progress display DisplaySet the machine to Pause by pressing the START/PAUSE button Cancelling a programmeAltering a programme which is running Opening the door after the programme has startedBefore the first wash Detergent dispenser drawerSorting out and preparing the laundry Preparing the wash cycleCotton 40 Weight of laundryTypes of fabric and care labels CottonDelicates Which detergent? Detergents and additivesTraditional Powders Which form?As a dryer, the machine works on the condensation principle Preparing the drying cycleLoad Garments not suitable for dryingFibre residue Drying symbols on garment labelsDuration of the drying cycle Modification of the drying timeAutomatic washing and drying NON-STOP programme Additional dryingAdd detergent and additive How to washSwitching the machine on Load the laundrySpin Speed button the correspond- ing light comes on Selection of the desired wash programmeSelection of the spin speed Selection of the Extra Rinse and/or Rinse Hold optionStarting the programme Selection of the Delay Start optionAt the end of the programme NON-STOP programme How to dryAutomatic washing and drying Drying onlyWash programmes Programme chartAdditional Max Duration Dry Special programmesDrying Detergent dispenser drawer Cleaning and maintenancePeriodical cleaning Exterior After each washWater inlet filter Drain filterEmergency emptying out Frost precautionsSomething not working? TroubleshootingProblem Noisy Feet have not been E00 White residue is left on the laundry Unsatisfactory washing resultsIf grey stains remain on the laundry Foam is still visible even after the last rinseThis appliance complies with the following EC directives Technical dataHelp us to help you Service & Spare PartsService & Spare Parts 0990 929Customer care Guarantee Conditions Italy Pordenone +39 1678 Sweden Stockholm +46 738 Slough +44 European GuaranteeSafety instructions for the installer Instructions for installation and electrical connectionRear view Front view and side viewTic bag and the previously removed screw InstallationUnpacking Carefully slide out the right poly- thene bagCarefully level by screwing PositioningLevelling Set the machineWater inlet cold water connection only Water drainageDo not connect to a hot water supply Electrical connections Interest of the environmentPermanent connection Hinges Preparation and assembly of the doorBuilding-in DoorCounter-magnet Mounting the doorSee Fig. H Drill four fixing holes see Fig. GBuilding-in