Electrolux 1271 VI manual Water inlet cold water connection only, Water drainage

Page 52

Installation

Water inlet (cold water connection only)

Before connect-
ing the hose be
sure to fit the
mesh filter «A»
supplied as per	A
diagram.
Installation
should comply

with local water

authority and building regulations’ requirements.

Set the hose correctly by loosening the ring nut. After positioning the inlet hose, be sure to tighten the ring nut again to prevent leaks.

Do not connect to a hot water supply.

Water drainage

The appliance drain hose should hook into a standpipe, the hook in the drain hose is formed using the plastic “U-Piece” supplied. The standpipe should have an internal diameter of approximately 38 mm (see dia- gram) thus ensuring there is an air break between the drain hose and standpipe.

When discharging into a stand- pipe ensure that the top of the curve in the hose end is no more than 90 cm (35.4”) and no less than 60 cm (23.6”) above floor level.

3 pin

Max. 90 cm.(35.4")

Min.60 cm.(23.6")

The upright standpipe should have a mini- mum length of 30 cm (12”) from the bottom of the elbow to the top of the pipe (see dia- gram). Make sure that it is designed in such a way that the end of the drain hose cannot be covered with water.

Longer drain hoses are available in lengths of 2.7 and 4 metres from your AEG Service Force Centre.

Min. 30 cm.(12")

38mm.(1/2 ") diameter standpipe

52

Image 52

Contents ÖKO-LAVAMAT 1271 VI Turbo Dear customer Contents Programme charts Technical data Service & Spare Parts Guarantee Conditions Bulding-inGeneral safety Safety instructionsInstallation Child safety During usePackaging materials DisposalMachine Tips for environmental protection Main features of your washer-dryer Description of the appliance Front viewControl panel Programme selector dialDelay Start button ON/OFF buttonMains-on light START/PAUSE buttonDrying Time button Programme Option buttonsPrewash Display Programme progress displayCancelling a programme Altering a programme which is runningOpening the door after the programme has started Set the machine to Pause by pressing the START/PAUSE buttonDetergent dispenser drawer Before the first washPreparing the wash cycle Sorting out and preparing the laundryWeight of laundry Types of fabric and care labelsCotton Cotton 40Delicates Detergents and additives Which detergent?Which form? Traditional PowdersPreparing the drying cycle LoadGarments not suitable for drying As a dryer, the machine works on the condensation principleDrying symbols on garment labels Duration of the drying cycleModification of the drying time Fibre residueAdditional drying Automatic washing and drying NON-STOP programmeHow to wash Switching the machine onLoad the laundry Add detergent and additiveSelection of the desired wash programme Selection of the spin speedSelection of the Extra Rinse and/or Rinse Hold option Spin Speed button the correspond- ing light comes onSelection of the Delay Start option Starting the programmeAt the end of the programme How to dry Automatic washing and dryingDrying only NON-STOP programmeProgramme chart Wash programmesSpecial programmes Additional Max Duration DryDrying Cleaning and maintenance Periodical cleaning ExteriorAfter each wash Detergent dispenser drawerDrain filter Water inlet filterFrost precautions Emergency emptying outTroubleshooting Something not working?Problem Noisy Feet have not been E00 Unsatisfactory washing results If grey stains remain on the laundryFoam is still visible even after the last rinse White residue is left on the laundryTechnical data This appliance complies with the following EC directivesService & Spare Parts Service & Spare Parts0990 929 Help us to help youCustomer care Guarantee Conditions European Guarantee Italy Pordenone +39 1678 Sweden Stockholm +46 738 Slough +44Instructions for installation and electrical connection Safety instructions for the installerFront view and side view Rear viewInstallation UnpackingCarefully slide out the right poly- thene bag Tic bag and the previously removed screwPositioning LevellingSet the machine Carefully level by screwingWater drainage Water inlet cold water connection onlyDo not connect to a hot water supply Interest of the environment Electrical connectionsPermanent connection Preparation and assembly of the door Building-inDoor HingesMounting the door Counter-magnetDrill four fixing holes see Fig. G See Fig. HBuilding-in