JVC PIM171200 manual To change the FM tuner selectivity, If Filter

Page 28

ENGLISH

To select the subwoofer cutoff frequency

—WooferFreq (only for KD-LX333R)

When a subwoofer is connected to this unit, select an appropriate cutoff frequency level for your subwoofer. When shipped from the factory, the subwoofer cutoff frequency is set to “FREQ MID.”

•FREQ LOW: Frequencies higher than 50 Hz are cut off to the subwoofer.

•FREQ MID: Frequencies higher than 80 Hz are cut off to the subwoofer.

•FREQ HIGH: Frequencies higher than 120 Hz are cut off to the subwoofer.

To adjust the line input level — LINE ADJ

(only for KD-LX333R)

Adjust the line input level properly when an external component is connected to the LINE INPUT plugs. When shipped from the factory, the line input level is set at level “00.”

If the input level of the connected component is not high enough, increase the input level properly. Without adjusting the line input level, you may be surprised at a loud sound when you change from the external component to another source.

To select the external component to use

––EXT INPUT (only for KD-LX111R)

You can connect the external component to the CD changer jack on the rear using the Line Input Adaptor KS-U57 (not supplied).

To use the external component as the playback source through this unit, you need to select which component – CD changer or external component – to use. When shipped from the factory, CD changer is selected as the external component.

•LINE INPUT: To use the external component other than CD changer.

•CD CHANGER:To use the CD changer.

Note:

For connecting the Line Input Adaptor KS-U57 and the external component, refer to the Installation/ Connection Manual (separate volume).

To make the front panel look flat (hiding the control panel) — FLAT PANEL

When operating the receiver using the remote control, you can hide the control panel to make the front panel look flat. When shipped from the factory, “FLAT OFF” is selected.

• FLAT ON:

The control panel will not come

 

out when you turn on the unit.

 

To use the control panel, press

 

4

so that the control

 

panel comes out. If no

 

operation is done for about 10

 

seconds, it automatically goes

 

back into the receiver.

• FLAT OFF:

You can use the control panel

 

normally.

Note:

When “FLAT ON” is selected, you can eject a CD by

holding 4 .

To change the FM tuner selectivity

—IF FILTER

In some areas, adjacent stations may interfere with each other. If this interference occurs, noise may be heard. This unit has been preset to automatically reduce this interference noise (“AUTO”) when shipped from the factory.

•

AUTO:

When this type of interference

 

 

occurs, this unit automatically

 

 

increases the tuner selectivity

 

 

so that interference noise will

 

 

be reduced. (But the stereo

 

 

effect will also be lost.)

•

WIDE:

Subject to the interference from

 

 

adjacent stations, but sound

 

 

quality will not be degraded

 

 

and the stereo effect will not be

 

 

lost.

28

Page 27 Page 29
Image 28
Page 27 Page 29
Contents Retain this password for future KD-LX333RKD-LX111R For Customer UseHow to reset your unit Position And Reproduction Of LabelsContents Location of the Buttons How to use the number buttonsControl panel Preparing the remote controller Installing the batteryRemote controller Turning on the power To drop the volume in a momentTo turn off the power Basic OperationsSetting the clock Finish the settingSet the hour Set the minuteSearching a station automatically Auto search Radio Basic OperationsSearching a station manually Manual search FM station automatic preset SSM Storing stations in memoryTune in to a station you want while M is flashing Select the FM band FM1 3 you want to store FM stations intoManual preset Select the band in this example, FM1Tune in to a station in this example, of 88.3 MHz SourceRDS Operations What you can do with RDSUsing TA Standby Reception Same programme can be received on Different frequenciesPress TP/PTY T to activate TA Standby Reception TP/PTY T againUsing PTY Standby Reception To store your favorite programme types To search your favorite programme type Than 2 seconds while listening to anFM station Select one of the PTY codesSetting the TA volume level Automatic clock adjustmentChanging the display mode while listening to an FM station FrequencyPTY codes CD Operations Playing a CDTo stop play and eject the CD Open the loading slotLocating a track or a Prohibiting CD ejection Playing a CD TextTo play back only intros Intro Scan Sound Adjustments What is BBEII?FAD BBESelect the sound mode you want For Preset valuesActivate custom equalizer CEQ User Rock Classic Jazz HIP HOP PopsStoring your own sound adjustments Select the items you want to adjustRepeat steps 4 and 5 to adjust the other items Repeat the same procedure to store other sound modesBasic Procedure Preferred Setting Mode PSM itemsOther Main Functions 24H/12HPress SEL S to finish the setting To select the dimmer mode Dimmer To adjust the display contrast levelTo select the scroll mode Scroll To set the clock display Clock DispTo change the FM tuner selectivity To adjust the line input level Line ADJ Only for KD-LX333RIf Filter To adjust the volume increase rate Mode changes as followsCruise 1 Cruise Cruise OFF As you turn the control dial, the Audio CruiseAssigning names to the sources If Audio Cruise does not function correctlySelect a source you want to assign a name to Sources Maximum numberTo erase the input characters Select the character set you want while is flashingSelect a character Available charactersRegistering the password Using the security lockHow to Use the Provided Code Sticker When Security Lock works? To change the passwordCD Changer Operations Playing CDsSelect the CD automatic changer CD-CH To go to the next tracks or the previous tracksSelecting CD playback modes To go to a particular disc directlyTo show the CD Text information PlayREPEAT1 REPEAT2 To play back tracks repeatedly RepeatINTRO1 INTRO2 Using a subwoofer Adjusting the sound onSelect the external component Operate the external componentWhat is DAB system? DAB Tuner OperationsStoring DAB services in memory Select a service you want to listen toService name Ensemble name Channel number Frequency To tune in a particular ensemble without searchingTuning in to a preset DAB service To adjust the DAB volume level While receiving a DAB serviceWhat you can do more with To use Alternative ReceptionTroubleshooting Symptoms Causes RemediesNo MAG appears on No magazine is loaded Insert the magazine Appears on Security lock is in use Enter the passwordLonger screws than specified Maintenance Handling CDsSpecifications FM TunerMW Tuner LW TunerHaving Trouble with operation? Pour mettre de nouveau la démonstration en service So deaktivieren Sie die DemonstrationRépétez la même procédure et choisissez Demo on à l’étape Zo annuleert u de demonstratieFuse blows No sound from the speakersSound is distorted Unit becomes hotEinbau auf jeden Fall aufbewahren Bewaar de hendels nadat u het apparaat hebt geïnstalleerdOriginal wiring Modified wiringUse modified wiring 2 if the unit does not turn on See diagram CKoppel de speakers van dit apparaat los en Verbind ze aan de versterkerSpeaker leads of this unit unused ’enceintes de cet appareil inutilisés
Top Page Image Contents