Whirlpool W10558490A Direct Wire Connection, Connect neutral wire, If your wiring looks like this

Page 12

3.Connect the other wires to outer terminal block screws. Tighten screws.

4.Tighten strain relief screws (E).

5.Insert tab of terminal block cover into slot of dryer rear panel. Secure cover with hold-down screw.

6.You have completed your electrical connection. Now go to “Venting Requirements.”

3-Wire Power Supply Cord Connection

IMPORTANT: Use where local codes permit connecting cabinet-ground conductor to neutral wire.

Direct Wire Connection

Direct Wire Strain Relief

1. Attach direct wire strain relief

H

3-wire receptacle (NEMA type 10-30R)

Spade terminals with upturned ends

3-prong plug

Ring terminals

I

J

Unscrew the removable conduit connector (H) and any screws from a 3/4" (19 mm) UL listed strain relief (UL marking on strain relief). Put the threaded section of the strain relief

(J) through the hole below the terminal block opening (I).

Reaching inside the terminal block opening, screw the

removable conduit connector (H) onto the strain relief threads.

1. Connect neutral wire

A

D

E

Remove center terminal block screw (A). Connect neutral wire

(D)(white or center wire) of power supply cord (E) to the center, terminal screw of the terminal block (A). Tighten screw.

2.Connect the other wires to outer terminal block screws. Tighten screws.

3.Tighten strain relief screws (E).

4.Insert tab of terminal block cover into slot of dryer rear panel. Secure cover with hold-down screw.

5.You have completed your electrical connection. Now go to “Venting Requirements.”

2. Attach direct wire cable to strain relief

Put direct wire cable through the strain relief. The strain relief should have a tight fit with the dryer cabinet and be in a horizontal position. Tighten strain relief screw against the direct wire cable.

If your wiring looks like this:

4-wire direct connection:

Go to “4-Wire Direct Connection” on page 13.

3-wire direct connection:

Go to “3-Wire Direct Connection” on page 14.

12

Page 11 Page 13
Image 12
Page 11 Page 13
Contents WASHER/DRYER Safety Table of ContentsWASHER/DRYER Safety Installation Requirements Tools needed Optional toolsParts supplied If you have You will need Recessed area or closet installation Mobile Home Additional Installation RequirementsMobile home installations require Location RequirementsDIMENSIONS/CLEARANCES DimensionsClearances Front View Side View Back ViewDrain System Floor standpipe drain systemWall standpipe drain system Floor drain systemElectrical Requirements It is your responsibilityElectrical Connection Install rear leveling legs Install front leveling legsOpen washer lid and pull out foam packing ring Electrical Connection Choose electrical connection typeRemove terminal block cover Power Supply Cord Connection Attach power supply cordConnect neutral ground wire and neutral wire Connect ground wireDirect Wire Connection Direct Wire Strain Relief Attach direct wire strain reliefConnect neutral wire Attach direct wire cable to strain reliefWire Direct Wire Connection Prepare your 4-wire cable for direct connectionConnect other wires Prepare your 3-wire cable for direct connection Optional 3-Wire ConnectionVenting Venting RequirementsRecommended exhaust installations Optional exhaust installationsAlternate installations for close clearances Plan Vent SystemInstall Vent System Install exhaust hoodSpecial provisions for mobile home installations Connect vent to exhaust hoodAttach drain hose to drain connector Remove drain hose form floor drain installations onlyConnect Drain Hose Attach clamp to drain hoseConnect Inlet Hoses Connect Inlet Hoses Connect Vent Check for leaks Connect vent to exhaust outletSecure drain hose Laundry Tub Standpipe WallAdjust leveling legs Level WASHER/DRYERCheck levelness of washer/dryer Plug into a grounded 3- or 4-prong outletComplete Installation Checklist If the dryer will not start, check the followingPage TM 2013 Whirlpool. All rights reserved
Top Page Image Contents