Whirlpool W10558490A installation instructions If you have You will need

Page 4

INSTALLATION REQUIREMENTS

TOOLS AND PARTS

Parts needed: (Not supplied with washer/dryer)

nVent clamps

nVent elbows and ductwork

Check local codes, electrical supply and venting, and read “Electrical Requirements” and “Venting Requirements” before purchasing parts. Mobile home installations require metal exhaust system hardware available for purchase from the dealer from whom you purchased your washer/dryer. For further information, please reference the “Assistance or Service” section of the Washer/Dryer Use and Care Guide.

Optional equipment: (Not supplied with washer/dryer)

Refer to your Use and Care Guide for information about accessories available for your washer/dryer.

Alternate parts: (Not supplied with washer/dryer)

Your installation may require additional parts. To order, please refer to toll-free numbers on back page of your Use and Care Guide.

If you have:

You will need:

Overhead sewer

Standard 20 gal. (76 L) 39" (990 mm)

 

tall Drain Tub or Utility Sink, Sump

 

Pump and Connectors (available from

 

local plumbing suppliers)

Floor drain

Siphon Break Part Number 285320,

 

Additional Drain Hose Part Number

 

285702, and Connector Kit Part

 

Number 285442

1" (25 mm) standpipe

2" (51 mm) diameter to 1" (25 mm)

 

diameter Standpipe Adapter

 

Part Number 3363920,

 

Connector Kit Part Number 285835

Laundry tub or

Sump pump system (if not already

standpipe taller than

available)

96" (2.4 m)

 

Drain hose too short

Extension Drain Hose

 

Part Number 285664,

 

Connector Kit Part Number 285442

Lint clogged drain

Drain Protector Part Number 367031,

 

Connector Kit Part Number 285835

Water faucets

2 longer water fill hoses:

beyond reach

6 ft (1.8 m) Part Number 76314,

of fill hoses

10 ft (3.0 m) Part Number 350008

4

Page 3 Page 5
Image 4
Page 3 Page 5
Contents WASHER/DRYER Safety Table of ContentsWASHER/DRYER Safety Tools needed Optional tools Installation RequirementsParts supplied If you have You will need Recessed area or closet installation Mobile Home Additional Installation RequirementsMobile home installations require Location RequirementsDIMENSIONS/CLEARANCES DimensionsClearances Front View Side View Back ViewDrain System Floor standpipe drain systemWall standpipe drain system Floor drain systemIt is your responsibility Electrical RequirementsElectrical Connection Install front leveling legs Install rear leveling legsOpen washer lid and pull out foam packing ring Choose electrical connection type Electrical ConnectionRemove terminal block cover Power Supply Cord Connection Attach power supply cordConnect neutral ground wire and neutral wire Connect ground wireDirect Wire Connection Direct Wire Strain Relief Attach direct wire strain reliefConnect neutral wire Attach direct wire cable to strain reliefPrepare your 4-wire cable for direct connection Wire Direct Wire ConnectionConnect other wires Prepare your 3-wire cable for direct connection Optional 3-Wire ConnectionVenting Venting RequirementsRecommended exhaust installations Optional exhaust installationsAlternate installations for close clearances Plan Vent SystemInstall Vent System Install exhaust hoodSpecial provisions for mobile home installations Connect vent to exhaust hoodAttach drain hose to drain connector Remove drain hose form floor drain installations onlyConnect Drain Hose Attach clamp to drain hoseConnect Inlet Hoses Connect Inlet Hoses Connect Vent Check for leaks Connect vent to exhaust outletSecure drain hose Laundry Tub Standpipe WallAdjust leveling legs Level WASHER/DRYERCheck levelness of washer/dryer Plug into a grounded 3- or 4-prong outletComplete Installation Checklist If the dryer will not start, check the followingPage TM 2013 Whirlpool. All rights reserved
Top Page Image Contents