Icom IC-208H instruction manual Push Func then LOW 6DTMF to turn Dtmf Dtmf encoder on

Page 64

9 DTMF MEMORY ENCODER

DProgramming a DTMF code— via microphone

zPush [FUNC] then [LOW 6(DTMF)] to turn the

DTMF DTMF encoder ON.

•“d” appears in place of 100 MHz digit.

x Push [SET B(D-OFF)] to enter the DTMF memory programming condition.

cPush [Y] or [Z] to select the desired DTMF

memory channel.

vPush the desired digit keys.

•When the first digit is input, previous memory con- tents are cleared automatically.

•“E” stands for “M” and “F” stands for “# .”

•Push [Y]/[Z] and repeat this step if you make a mistake.

•The S/RF indicator shows the digit group. The indi- cation increases every 6 digits.

bPush [VFO/LOCK] to exit the programming condition.

•The [CLR A(MW)] key cannot be used to exit. If pushed, code “A” is input. Reprogram in such a case.

[EXAMPLE]: Programming “5428AB453” into DTMF memory channel “D4.”

 

Push

then

.

Push

Push

Push

 

 

 

Push

49

Page 63 Page 65
Image 64
Page 63 Page 65
Contents I208H Word Definition Rwarning May occurEquipment damage may occur Personal injury, fire or electric shockPrecaution Operate this device under FCC regulationsSupplied Accessories Dtmf Memory Encoder Installation methods InstallationQuick Reference Guide Drill 4 holes where the mounting bracket is to be installed Using the mounting bracketLocation Microphone connection Separation cable connectionConnect the supplied microphone as illustrated below Detach the controller as belowDrill 2 or 4 holes where the bracket is to be installed Optional MB-58 installationWhen using the optional MB-65 Battery connection DC power supply connectionConnecting to a DC Power Source Connecting to a DC Power SupplyAntenna installation Antenna connectorAntenna uses a PL-259 connector Antenna locationYour first contact IC-208H has 2 m and 70 cm transmittable bandsPush Band to select the desired frequency band You can select the desired frequency band from the HM-133Tune the frequency Setting duplex Repeater operationPush Func then CLR AMW Programming memory channelsPush and hold S.MWMW for 1 sec. to program Panel Description Front panel- controller2BAND Switch Band 0MEMORY/CALLPRIORITY Switch M/CALLPRIO4CONTROLLER Release Latch QTRANSMIT Indicator WDUPLEX Indicators pETONE Indicators Function display2MEMORY Channel Number Indicators 5S/RF Indicators6OUTPUT Power Indicators 7BUSY IndicatorRear Panel Antenna InformationData Jack PIN Assignment 1MEMORY/CALL Switch MR/CALL 0BAND Switch BandMicrophone HM-133 Microphone keypad HoldingCancels frequency entry Cancels the scan or priority watch MingAtion is performed Ing the a to D, # and MkeysOptional Microphones HM-118N/TN/TAN Setting a Frequency DTurning power ON/OFFPreparation Dvfo and memory modesUsing the Y/Z keys Using the tuning dialUsing the keypad Tuning step selection Push Setlock to enter set modeSwitch the microphone keypad lock function Lock functionsFrequency lock DMicrophone keypad lockBasic Operation ReceivingMonitor function SQL Y DMUTE/ SQL Z #16KEY-L, respectivelyPush PWR to exit initial set mode Squelch attenuatorRF Indicator Power Output Selecting output powerTransmitting Audio mute function One-touch PTT functionPush PTT to transmit and push again to re- ceive Repeater Operation Repeater operation flow chartGeneral Push and hold PTT to transmit Accessing a repeaterRelease PTT to receive Set the receive frequency repeater output fre Push Simp 9TSQL to return to simplex opera- tionSubaudible tones Subaudible tonesSubaudible tone frequency list Dtmf tones Hz tonePush Band to select the desired frequency SET band Offset frequencyPush Y or Z to set the desired offset Frequency range and offset direction Setting the auto repeater function ON/OFFFrequency range Duplex direction General description Memory OperationMemory channel selection Rotate Dial to select the memory channel to be pro- grammed Programming a memory channelPush S.MWMW for 1 sec. to program Programming a memory channel via the microphone Copying memory contents Example Transferring memory channel 30 contents to channel Memory/callmemory/callSelect the memory/call channel to be transferred Rotate Dial to select the target memory channelRotate the tuning dial to select the desired character Programming channel namesPush Then push To select the channel. Push DTo indicate the channel name Push SET BD-OFF or ENT CT-OFF until ANM appearRotate Dial to select the memory channel to be cleared Memory clearingPush S.MWMW momentarily, then push S.MWMW again for 1 sec Rotate Dial to select the contents in the bank Push Y/Z to select the desired contents in the bankMemory bank selection Rotate Dial to select the desired bank, a to JPush MR/CALL then select the desired mem Memory bank settingOry channel via Y/Z or keypad Transferring bank contents Call channel selection Call Channel OperationCall channel transferring Programming a call channel Scan Operation Scan typesPush VFO/LOCK to select VFO mode for Memory mode for memory scanScan start/stop PreparationScan edges programming Example Programming 145.300 MHz into scan edges 1AProgramming scan edges via microphone Push Monidtmf to exit set mode Skip channel settingSelect a memory channel Rotate Dial to set the desired timer Scan resume conditionPriority watch types Priority WatchOrity watch starts Push M/CALLPRIO for 1 sec. to stop the watch Priority watch operationPush MR/CALL, then push Scan 2 to start the memory scan Dtmf Memory Encoder Programming a Dtmf codePush Monidtmf for 1 sec. to turn the Dtmf encoder on Push Monidtmf to exit Dtmf memory programming conditionPush Func then LOW 6DTMF to turn Dtmf Dtmf encoder on Push VFO/LOCK to exit the programming conditionAutomatic transmission Dtmf memory Transmitting a Dtmf codeTransmitting a Dtmf memory directly Mentarily, then push the desired Dtmf keys A to F Manual transmissionPush DTMF-S again to deactivate the Dtmf direct selection Pocket Beep and Tone Squelch Pocket beep operationWaiting for a call from a specific station Lect the Dtcs polarityCalling a waiting station using pocket beep Available tone frequency listTone/DTCS squelch operation Push TONET-SCAN for 1 sec. to start the tone scan Tone scanSelects the tone type to be scanned Set mode Other FunctionsDisplay dimmer Display colorRepeater tone Tone squelch toneTuning step Dtcs codeOffset frequency Dtcs polarityScan resume timer Memory name settingChannel skip setting Memory bank settingProgram scan skip setting Bank link settingMemory bank link function Turns weather alert function on and OFFInitial set mode Entering initial set modeDAuto power OFF Time-out timerKey-touch beep Squelch delay Cooling fan controlData transmission speed Microphone sensitivityDtmf speed Active bandNarrow TX function AM/FM narrow mode Push Band or MR/CALL to select the desiredTurn the weather alert function OFF in set mode Weather channel operationWeather channel selection Weather alert functionDefault setting Microphone keysUP/DN keys on a microphones 1/F-2 keys on HM-133Partial reset Cloning between transceivers Push Setlock on the master transceiverCloning using a personal computer Cloning errorPacket operation Bps packet operationData speed Connect the transceiver and a TNC as illustrated belowOther Functions Bps high speed packet operation Adjusting the transmit signal output from TNC Increase the TNC output levelTroubleshooting MaintenanceProblem Possible Cause Solution 20 a Fuse replacementFuse Specifications and Options SpecificationsDgeneral DtransmitterOptions OPC-347/OPC-1132 DC Power CablesOPC-600/600R*, OPC-601/601R* Separation Cables Mode Arrangement Mode Arrangement Kamiminami, Hirano-ku, Osaka 547-0003 Japan
Top Page Image Contents