Icom IC-208H instruction manual Push Then push To select the channel. Push

Page 47

MEMORY OPERATION 5

Channel names can also be programmed via the mi- crophone.

zPush [FUNC] then [CLR A(MW)] momentarily.

• “!” and memory channel number blink.

xPush [Y]/[Z] to select the memory/call channel to be as-

signed memory names.

cPush [BAND].

• Frequency readouts disappear and a cursor blinks.

nRepeat steps v and b until the desired channel names are displayed.

mPush [FUNC] then [CLR A(MW)] for 1 sec. to program the

name and exit the channel name programming condition.

vPush [Y]/[Z] to select the desired character.

• The selected character blinks.

bPush [SET B(D-OFF)] or [ENT C(T-OFF)] to move the cur- sor to left or right, respectively.

[EXAMPLE]: Programming “CLUB” into memory channel 1.

Push

, then push

. Push

to select the channel. Push

Push

to select the character

Push	or	to move the cursor. Repeat the
		previous
		steps.

Push , then push for 1 sec.

“Beep“

“Beep

“ Beep

“

Image 47

Contents I208H Personal injury, ﬁre or electric shock Word Definition RwarningMay occur Equipment damage may occurOperate this device under FCC regulations PrecautionSupplied Accessories Dtmf Memory Encoder Quick Reference Guide InstallationInstallation methods Location Using the mounting bracketDrill 4 holes where the mounting bracket is to be installed Detach the controller as below Microphone connectionSeparation cable connection Connect the supplied microphone as illustrated belowWhen using the optional MB-65 Optional MB-58 installationDrill 2 or 4 holes where the bracket is to be installed Connecting to a DC Power Supply Battery connectionDC power supply connection Connecting to a DC Power SourceAntenna location Antenna installationAntenna connector Antenna uses a PL-259 connectorYou can select the desired frequency band from the HM-133 Your ﬁrst contactIC-208H has 2 m and 70 cm transmittable bands Push Band to select the desired frequency bandTune the frequency Repeater operation Setting duplexPush and hold S.MWMW for 1 sec. to program Programming memory channelsPush Func then CLR AMW Front panel- controller Panel Description4CONTROLLER Release Latch 0MEMORY/CALLPRIORITY Switch M/CALLPRIO2BAND Switch Band Function display QTRANSMIT IndicatorWDUPLEX Indicators p ETONE Indicators7BUSY Indicator 2MEMORY Channel Number Indicators5S/RF Indicators 6OUTPUT Power IndicatorsAntenna Information Rear PanelData Jack PIN Assignment Microphone HM-133 0BAND Switch Band1MEMORY/CALL Switch MR/CALL Holding Microphone keypadIng the a to D, # and Mkeys Cancels frequency entryCancels the scan or priority watch Ming Ation is performedOptional Microphones HM-118N/TN/TAN Dvfo and memory modes Setting a FrequencyDTurning power ON/OFF PreparationUsing the keypad Using the tuning dialUsing the Y/Z keys Push Setlock to enter set mode Tuning step selectionDMicrophone keypad lock Switch the microphone keypad lock functionLock functions Frequency lockSQL Y DMUTE/ SQL Z #16KEY-L, respectively Basic OperationReceiving Monitor functionSquelch attenuator Push PWR to exit initial set modeTransmitting Selecting output powerRF Indicator Power Output Push PTT to transmit and push again to re- ceive One-touch PTT functionAudio mute function General Repeater operation ﬂow chartRepeater Operation Release PTT to receive Accessing a repeaterPush and hold PTT to transmit Push Simp 9TSQL to return to simplex opera- tion Set the receive frequency repeater output freSubaudible tone frequency list Subaudible tonesSubaudible tones Hz tone Dtmf tonesPush Y or Z to set the desired offset Offset frequencyPush Band to select the desired frequency SET band Frequency range Duplex direction Setting the auto repeater function ON/OFFFrequency range and offset direction Memory channel selection Memory OperationGeneral description Push S.MWMW for 1 sec. to program Programming a memory channelRotate Dial to select the memory channel to be pro- grammed Programming a memory channel via the microphone Copying memory contents Rotate Dial to select the target memory channel Example Transferring memory channel 30 contents to channelMemory/callmemory/call Select the memory/call channel to be transferredProgramming channel names Rotate the tuning dial to select the desired characterPush Then push To select the channel. Push Push SET BD-OFF or ENT CT-OFF until ANM appear DTo indicate the channel namePush S.MWMW momentarily, then push S.MWMW again for 1 sec Memory clearingRotate Dial to select the memory channel to be cleared Rotate Dial to select the desired bank, a to J Rotate Dial to select the contents in the bankPush Y/Z to select the desired contents in the bank Memory bank selectionOry channel via Y/Z or keypad Memory bank settingPush MR/CALL then select the desired mem Transferring bank contents Call channel transferring Call Channel OperationCall channel selection Programming a call channel Scan types Scan OperationPreparation Push VFO/LOCK to select VFO mode forMemory mode for memory scan Scan start/stopExample Programming 145.300 MHz into scan edges 1A Scan edges programmingProgramming scan edges via microphone Select a memory channel Skip channel settingPush Monidtmf to exit set mode Scan resume condition Rotate Dial to set the desired timerOrity watch starts Priority WatchPriority watch types Push MR/CALL, then push Scan 2 to start the memory scan Priority watch operationPush M/CALLPRIO for 1 sec. to stop the watch Push Monidtmf to exit Dtmf memory programming condition Dtmf Memory EncoderProgramming a Dtmf code Push Monidtmf for 1 sec. to turn the Dtmf encoder onPush VFO/LOCK to exit the programming condition Push Func then LOW 6DTMF to turn Dtmf Dtmf encoder onTransmitting a Dtmf memory directly Transmitting a Dtmf codeAutomatic transmission Dtmf memory Push DTMF-S again to deactivate the Dtmf direct selection Manual transmissionMentarily, then push the desired Dtmf keys A to F Lect the Dtcs polarity Pocket Beep and Tone SquelchPocket beep operation Waiting for a call from a speciﬁc stationAvailable tone frequency list Calling a waiting station using pocket beepTone/DTCS squelch operation Selects the tone type to be scanned Tone scanPush TONET-SCAN for 1 sec. to start the tone scan Other Functions Set modeTone squelch tone Display dimmerDisplay color Repeater toneDtcs polarity Tuning stepDtcs code Offset frequencyMemory bank setting Scan resume timerMemory name setting Channel skip settingTurns weather alert function on and OFF Program scan skip settingBank link setting Memory bank link functionEntering initial set mode Initial set modeKey-touch beep Time-out timerDAuto power OFF Microphone sensitivity Squelch delayCooling fan control Data transmission speedNarrow TX function Active bandDtmf speed Push Band or MR/CALL to select the desired AM/FM narrow modeWeather alert function Turn the weather alert function OFF in set modeWeather channel operation Weather channel selection1/F-2 keys on HM-133 Default settingMicrophone keys UP/DN keys on a microphonesPartial reset Push Setlock on the master transceiver Cloning between transceiversCloning error Cloning using a personal computerConnect the transceiver and a TNC as illustrated below Packet operationBps packet operation Data speedOther Functions Bps high speed packet operation Increase the TNC output level Adjusting the transmit signal output from TNCProblem Possible Cause Solution MaintenanceTroubleshooting Fuse Fuse replacement20 a Dtransmitter Specifications and OptionsSpeciﬁcations DgeneralOPC-600/600R*, OPC-601/601R* Separation Cables OPC-347/OPC-1132 DC Power CablesOptions Mode Arrangement Mode Arrangement Kamiminami, Hirano-ku, Osaka 547-0003 Japan