Toshiba TOSVERT VF-AS1 Transmission errors, Format error Data transmission format does not match

Page 21

efesotomasyon.com -Toshiba inverter,drive,servo,plc

E6581315

4.3. Transmission errors

Table of error codes

Error name			Description	Error code

Impossible to	exe-	The command is impossible to execute, though communication was		0000
cute		established normally.
		1 Writing data into a parameter whose setting cannot be changed
		during operation (e.g., maximum frequency) *1
		2 Writing data into a parameter while “” is in progress
Data error		Invalid data is specified.		0001
Communication		There is no communication number that matches.		0002
number error
Command error		The command specified does not exist.		0003 (ASCII mode)
				No code returned (Binary
				mode)
Checksum error		The Checksum does not match.		0004
Format error		The data transmission format does not match.		No code returned
		1 One-digit inverter number (ASCII mode)
		2 The CR code is found in the designated position. (ASCII mode)
		Ex.:Communication number of 4 digit or less. In the case of (R11)
		CR, 11) CR is recognized as a communication number and
		the CR code is not recognized, with the result that a format
		error occurs.
		3 A code other then the stop code (“)”) is entered in the stop code
		position.
Receiving error		A parity, overrun or framing error has occurred. *2		No code returned
	*1: For parameters whose settings cannot changed during operation, see ”Table of parameters.”
	*2: Parity error		: The parity does not match.
		Overrun error	: A new data item is entered while the data is being read.

Framing error : The stop bit is placed in the wrong position.

*For the errors with “no code returned” in the above table, no error code is returned to avoid a data crash.

If no response is received, the computer side recognizes that a communication error has occurred. Retry after a lapse of some time.

*If the inverter number does not match, no processing will be carried out and no data will be re- turned, though it is not regarded as an error.

20

Image 21

Contents E6581315② Tosvert VF-AS1 Series RS485 Communication FunctionE6581315 Read first Safety precautionsContents General outlines of the communication function BIT15 BIT8BIT7 BIT0Bit Word BIT2 Data transmission specificationsCommunication protocol About the handling of received framesMOUBUS-RTU Toshiba Inverter Protocol Binary mode 2FHData transmission format Data transmission format used in Ascii modeINV-NO CMD Data28H Bytes Checksum area 5bytes BlankData SUM INV-NOData transmission format used in binary mode Returned for the 57H W and 50H P commands Command receivedByte Bytes Sum 1 bytes Checksum not omissible 00H to FFH2FH Byte 4EH6EH Bytes NornTransmission format of Block Communication Page Bytes Blank Start Code INV-NO Dummy data is required for this command CommandsReads the data with the specified communication number Block communication Computer InverterRFE03077BCR RFE03CRPage Transmission errors Format error Data transmission format does not matchCommunication There is no communication number that matches Broadcast communication function VF-AS1 Ascii mode Computer → Inverter Inverter → Computer Examples of the use of communication commandsFrom the computer H = 24d  trip status RFC90CRExamples of Communication programs Next =LENS$ For I=1 to LInput #1,B$ Goto160 T=TIMER COUNT=TIMER-T If Count 0 then T=TIMERPrint #1,B$ Page End If MSComm1.Output = Text2.Text & Chr13 End SubText2.Text = Text1.Text = End Sub Inverter number  MODBUS-RTU protocolRead command MODBUS-RTU transmission formatCRC Blank Command 1 byte Write command5bytes Blank Command 1 byte Text size is 8 bytes fixed InverterCRC Generation Error codesBit counter = End Return CRCInter-drive communication Never use pin-7 P11 QWiring 4-wire RS485 communication） E6581315 QWiring 2-wire RS485 communicationPage Parameters relating to the slave side example =0.01% Proportional control of speed90.00Hz 45.00Hz Slave 100.00Hz 00%Slave 100.00Hz1 00% 80.00Hz 40.00HzINV-NO 1 byte Inverter number Transmission format for inter-drive communication0OFF Communication parametersMODBUS-RTU Inverter number Baud rate,  , Parity PC → INV „ Timer Time-out period Computer linkMaster INV To Slave INV INV → PC PC → INVSend waiting time ,  Free notesUse this function for the following case Communication commands commands from the computer Commands and monitoring from the computerPI OFF OFFForcibly braked Preliminary excitation Electric Power quantityBrake release B Braking answer BAWire RS485 communication FA32 „ FM analog output FA51 „ Terminal board output data FA50„ AM analog output FA52 Output terminal no Specified data outputMonitoring from the computer RFD00CRUnit 0.01% N·m RES „ Input terminal board status FD06, FE06Input terminal function selection 9 f119 BIT15„ Output terminal board status FD07, FE07 ST=ON ST=OFF „ Inverter operating status 1 FD01, FE01„ Inverter operating status 3 FD49, FE49 „ Inverter operating status 2 FD42, FE42„ Inverter operating command mode status FD45, FE45 „ Inverter operating frequency mode status FD46, FE46Preset speed operation „ Alarm information monitor FC91 „ Cumulative operation time alarm monitor FE79Bit Specifications Remarks E6581315 Model Data „ Inverter model capacity code FB05LED setting by communication Parameter Name Range SettingUtilizing panel LEDs and keys by communication „ Block Communication Function for LED Display Blank Ascii LED display data code 00H-1FH are blankKey utilization by communication FA10=0FA10=1 Parameter data ROM EEPPage FE02 Frequency command value 01Hz Alarm codeFE19 Torque command FE29 Input powerTion FE80 Cumulative power on time E6581315 FD50 Light-load high-speed torque 01%FE84 Binary input value option Can Appendix 1 Table of data codesSUB ESCResponse time „ Data transmission time Appendix 2 Response timeVF-A7 Appendix 3 Compatibility with the communication functionAppendix 4 Troubleshooting Appendix 5 Connecting for RS485 communication RXB RXATXA TXB

Related manuals

Manual 326 pages 49.22 Kb

Manual 10 pages 12.86 Kb