Furuno FR-2125V installation manual Safety Instructions

Page 3

SAFETY INSTRUCTIONS

WARNING

Radio Frequency Radiation Hazard

The radar antenna emits electromagnetic radio frequency (RF) energy which can be harmful, particularly to your eyes. Never look directly into the antenna aperture from a close distance while the radar is in operation or expose yourself to the trans- mitting antenna at a close distance.

Distances at which RF radiation levels of 100 and 10 W/m2 exist are given in the table below.

Note: If the antenna unit is installed at a close distance in front of the wheel house, your administration may require halt of transmission within a certain sector of antenna revolution. This is possible—Ask your FURUNO representative or dealer to provide this feature.

 

Radiator

Distance to

Distance to

Model

100 W/m2

10 W/m2

type

 

point

point

 

 

 

 

 

 

 

XN12AF

 

 

FR-2125V

 

Worst case

Worst case

XN20AF

1.1 m

10.0 m

 

 

 

XN24AF

 

 

 

 

 

 

WARNING

 

Do not open the equipment

 

unless totally familiar with

 

electrical circuits and

 

service manual.

ELECTRICAL

Only qualified personnel

should work inside the

SHOCK

HAZARD

equipment.

 

 

 

Wear a safety belt and hard

 

hat when working on the

 

antenna unit.

Serious injury or death can result if someone falls from the radar antenna mast.

Construct a suitable service platform from which to install the antenna unit.

Serious injury or death can result if some- one falls from the radar antenna mast.

Turn off the power at the mains switch- board before beginning the installation.

Fire, electrical shock or serious injury can result if the power is left on or is applied while the equipment is being installed.

Do not install the display unit where it may get wet from rain or water splash.

Water in the display unit can result in fire, electrical shock or equipment damage.

i

Image 3
Contents Installation Manual Marine Radar FR-2125V 00080875300 Safety Instructions Use only the specified power cable System Configuration Name Type Code No Qty Remarks Standard SupplyName Type Code No Remarks Optional EquipmentMounting considerations Antenna UnitAssembling the antenna unit Be sure to remove the guide pinsFastening the radiator to the radiator bracket Fastening the antenna unit to the mounting platformAntenna unit, front view Tabletop mounting Mounting procedureDisplay Unit Before mounting the display unitStay Setting catch to hole in stay Console type mounting 12 How to dismount the PTU coverName Type Qty Code No Remarks Display unit modification procedureSeparating the control head Separate type control head kit Type OP03-157, Code No13 How to dismount covers 14 Clamp position 15 Detaching the control head Plate Control head modification procedure17 Attaching the handle plate Wiring between display unit and control head18 How to attach KB fixing plate Wiring Antenna unit, front view, cover removed Correct seating of waterproofing gasket Fabricating signal cable S03-75 Power Switch Power Switch in AC Powered Display UnitDPYCY-3.5 Fabricating the AC power cable suppliedCVV-S 8X2C Fabricating the DC power cable CVV-S 8X2C, optionLeading cables into the display unit Cable fed from rear of display unit Default methodCables fed from bottom of display unit for console mount Cable fed from outside display unitM4X8 2 pcs ConnectionsInput/Output Signal Connectors on the INT BoardJP91 JP92 Changing AC Power SpecificationHow to attach NH connector Power Spec AntennaRestoring default settings Tuning InitializationAccessing Menus for Initialization and Adjustment Adjusting Video Signal LevelPicture appears Deviated counterclockwise Heading AlignmentSuppressing Main Bang Adjusting Sweep TimingMagnetron heater voltage rating Confirming Magnetron Heater VoltagePress Radar Menu 0 0 0 Initial Setting MenusInitial SETTING1 menu Initial SETTING2 menuInitial SETTING3 menu OWN Ship Information menu Initial SETTING4 menuInstallation and connection of the Gyro Converter Board Gyro Converter GC-8Name Type Qty Code No INT Board Gyro Converter Board J446 4P J465 6P 14P Connection of external power supply DIP switch, jumper wire settingsDefault setting Stator voltage GyrocompassFrequency Remarks Rotor voltageInterval SW2-4JP1 JP2 JP3 JP4 JP5 SW1 Setting the heading readout on the radar displayName Type Qty Code No ARP Board 18P9002B 008-473-650 Installation of the ARP boardARP board adjustment ARP Board ARP-26ARP Board 18P9002B Final checkTable top/console type RP Board RP-26Fastening the M-card base assy. to the right arm cover Necessary parts RP-26-Z-2E Code no Separate type control head13 Display pedestal, front view 14 Display pedestal, front and top views Necessary parts PM-30 and OP03-150 Code no Performance Monitor PM-30Alarm Kit ProcedureNecessary parts OP03-156 Code no 16 Display unit, inside view AC-DC Conversion Kit 03P9246A 008-487-44003P9246C 008-493-700 Board Filter RDP-124 DC 008-492-460 Connection of Rate-of-Turn Signal ConnectionChecking operation Necessary parts OP03-164 Code no Console Kit20 How to fasten the edge guard Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page