Furuno FR-2125V installation manual Power Switch in AC Powered Display Unit

Page 27

2.2 Display Unit

Two cables are terminated at the display unit: the signal cable S03-75 and the power cable. The signal cable comes with a connector preattached to it for con- nection to the display unit. Fabricate the power cable as shown on the next page.

POWER Switch in AC

Powered Display Unit

The display unit designed to run on AC power has a power switch inside its base which cuts off 100/200 VAC power to the display unit. Pull the display unit forward several centimeters to access the switch. TURN THE SWITCH OFF (as well as the main POWER switch)

WHENEVER ACCESSING INSIDE THE DISPLAY UNIT.

POWER Switch

J446

J466

J462

Display unit, inside view

2-5

Image 27

Contents Installation Manual Marine Radar FR-2125V 00080875300 Safety Instructions Use only the specified power cable System Configuration Name Type Code No Qty Remarks Standard SupplyName Type Code No Remarks Optional EquipmentMounting considerations Antenna UnitAssembling the antenna unit Be sure to remove the guide pinsFastening the radiator to the radiator bracket Fastening the antenna unit to the mounting platformAntenna unit, front view Tabletop mounting Mounting procedureDisplay Unit Before mounting the display unitStay Setting catch to hole in stay Console type mounting 12 How to dismount the PTU coverName Type Qty Code No Remarks Display unit modification procedureSeparating the control head Separate type control head kit Type OP03-157, Code No13 How to dismount covers 14 Clamp position 15 Detaching the control head Plate Control head modification procedure17 Attaching the handle plate Wiring between display unit and control head18 How to attach KB fixing plate Wiring Antenna unit, front view, cover removed Correct seating of waterproofing gasket Fabricating signal cable S03-75 Power Switch Power Switch in AC Powered Display UnitDPYCY-3.5 Fabricating the AC power cable suppliedCVV-S 8X2C Fabricating the DC power cable CVV-S 8X2C, optionLeading cables into the display unit Cable fed from rear of display unit Default methodCables fed from bottom of display unit for console mount Cable fed from outside display unitM4X8 2 pcs ConnectionsInput/Output Signal Connectors on the INT BoardJP91 JP92 Changing AC Power SpecificationHow to attach NH connector Power Spec AntennaRestoring default settings Tuning InitializationAccessing Menus for Initialization and Adjustment Adjusting Video Signal LevelPicture appears Deviated counterclockwise Heading AlignmentSuppressing Main Bang Adjusting Sweep TimingMagnetron heater voltage rating Confirming Magnetron Heater VoltagePress Radar Menu 0 0 0 Initial Setting MenusInitial SETTING1 menu Initial SETTING2 menuInitial SETTING3 menu OWN Ship Information menu Initial SETTING4 menuInstallation and connection of the Gyro Converter Board Gyro Converter GC-8Name Type Qty Code No INT Board Gyro Converter Board J446 4P J465 6P 14P Connection of external power supply DIP switch, jumper wire settingsDefault setting Stator voltage GyrocompassFrequency Remarks Rotor voltageInterval SW2-4JP1 JP2 JP3 JP4 JP5 SW1 Setting the heading readout on the radar displayName Type Qty Code No ARP Board 18P9002B 008-473-650 Installation of the ARP boardARP board adjustment ARP Board ARP-26ARP Board 18P9002B Final checkTable top/console type RP Board RP-26Fastening the M-card base assy. to the right arm cover Necessary parts RP-26-Z-2E Code no Separate type control head13 Display pedestal, front view 14 Display pedestal, front and top views Necessary parts PM-30 and OP03-150 Code no Performance Monitor PM-30Alarm Kit ProcedureNecessary parts OP03-156 Code no 16 Display unit, inside view AC-DC Conversion Kit 03P9246A 008-487-44003P9246C 008-493-700 Board Filter RDP-124 DC 008-492-460 Connection of Rate-of-Turn Signal ConnectionChecking operation Necessary parts OP03-164 Code no Console Kit20 How to fasten the edge guard Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page