Xantrex Technology TS400 manual Hardwiring the AC Output, To hardwire the AC output connections

Page 41

Installing the TS400

Step 9: Hardwiring the AC Output

If you wish to permanently connect additional AC outlets, Xantrex recommends hardwiring the AC output connections.

WARNING: Fire, shock, and energy hazards

Make sure wiring is disconnected from all electrical sources before handling. All wiring must be done in accordance with local and national electrical wiring codes. Do not connect the output leads of the inverter to any incoming AC source.

To hardwire the AC output connections:

1.Turn the On/Standby switch to Standby ( ).

2.Remove the knockout using a slot screwdriver as shown in Figure 2-6. Do not leave the knockout inside the wiring box.

Figure 2-6Removing the Knockout

975-0055-01-01

2–19

Image 41
Contents TS400 Sine Wave Inverter Page TS400 Sine Wave Inverter DWHDQG5HYLVLRQ Scope PurposeAudience OrganizationConventions Used Related Information Acronyms and TerminologyPage General Precautions Important Safety InstructionsExplosive Gas Precautions Precautions When Working With BatteriesFCC Information to the User Page Contents Specifications TroubleshootingBattery Types and Sizes Operation975-0055-01-01 Xiii Xiv Introduction How TS400 Works Premium Power and Ease of Use7KLVSURWHFWLRQIHDWXUH« Comprehensive ProtectionHdwxuh Hvfulswlrq TS400 FeaturesFront Panel Hvfulswlrq Back PanelPart number of Remote Switch Optional Accessory Remote SwitchDimensions of Remote Switch Installation Inverter IntroductionInstallation Codes Preparing for InstallationMaterials List Installation Tools and MaterialsMaterials for AC output hardwiring Overview Installing the TS400Designing Your Installation Choosing a Location Battery Requirements Hdfkfdeoh DC CablesTo mount your TS400 Mounting Your InverterTo connect the chassis ground Connecting the Chassis GroundTo install the remote switch Installing the Optional S400 Remote Switch3Connecting Cable to the TS400 To prepare the DC cables Getting Ready to Connect the DC CablesGuidelines for Routing the DC Cables Routing the DC Cables5Connection Order for DC Cables Connecting the DC CablesTo connect the DC cables To connect your AC equipment to the Gfci outlets Connecting Your Equipment to the Gfci OutletsTo hardwire the AC output connections Hardwiring the AC Output7Removing the 3 Screws on the Wiring Box Access Panel 8Completing the Hardwiring To test the TS400 Testing Your InstallationPerforming Checks Prior to Initial Start-up 9Inverter Dimensions 10S400 Remote Switch Mounting Template Scale approximately Operation Panel of the TS400 on page 1-4 in the Introduction chapter Front Panel FeaturesOperating the TS400 Turning the TS400 to Standby When Not in UseTurning the TS400 On To turn the TS400 on2S400 Remote Switch Using the Optional S400 Remote SwitchTo recover from a low battery voltage shutdown Recovering from Low Battery Voltage ShutdownRecharging Your Batteries Restarting or Operating Multiple Pieces of EquipmentLjkw Roru 6WDWXV $FWLRQ Monitoring the Operating StatusDxow 6WDWXV $FWLRQ Resetting After a Fault or ShutdownPage Troubleshooting Front Panel Troubleshooting Reference3UREOHP 3RVVLEOH&DXVH 1Troubleshooting Reference3UREOHP 3RVVLEOH&DXVH 6ROXWLRQ Specifications Physical Specifications with Projections Electrical SpecificationsFan Cooling System Regulatory ApprovalsPage Battery Types and Sizes Deep-Cycle Batteries Battery TypesAutomotive Starting Batteries Battery Size Battery Sizing Example Estimating Battery RequirementsTo determine how much battery capacity you need 7LPHSHUD\ Dssoldqfh $SSOLDQFH Dwwv +RXUVBattery Sizing Worksheet Two Batteries Connected In Parallel Using Multiple BatteriesTwo Separate Battery Banks Battery Tips 6WDWHRI&KDUJH Warranty Warranty and Product InformationExclusions DisclaimerProduct Out of Warranty Service Return Material Authorization PolicyReturn Procedure Information About Your System Information About Your SystemIndex IX-2 975-0055-01-01 IX-3 IX-4 Page Xantrex Technology Inc