Lowrance electronic X52, X59DF manual Lock washer Bolt Nut Flat washer

Page 14

Lock washer

Bolt

Nut

Flat washer

Flat washer

Assemble transducer and bracket.

3.Assembling the transducer.

A. One-piece bracket: Once you determine the correct position for the ratchets, assemble the transducer as shown in the following figure. Don't tighten the lock nut at this time.

Metal

Nut washer

Rubber

washers

Metal washer

Bolt

Assemble transducer and bracket.

B. Two-piece bracket: Once you determine the correct position for the ratchets, assemble the transducer as shown in the figure in step 2B. Don't tighten the lock nut at this time.

4.Drilling mounting holes.

Hold the transducer and bracket assembly against the transom. The transducer should be roughly parallel to the ground. The transducer's centerline should be in line with the bottom of the hull. Don't let the bracket extend below the hull!

Mark the center of each slot for the mounting screw pilot holes. You will drill one hole in the center of each slot.

10

Image 14

Contents X52 and X59DF Lowrance Electronics Inc 12000 E. Skelly Dr Tulsa, OK USA Table of Contents Fish I.D. Fish Symbols & Depths Capabilities and Specifications X52 and X59DF IntroductionFeet 244 meters at 200 kHz 1500 feet Transducer Installation PreparationsSingle-frequency trolling motor installations Single-frequency transom installationsDual-frequency transom installations Shoot-through hull installationsPad Deadrise less than Strakes Good location Poor location Location Poor angleTransom Transducer centerline Hull bottom Dot Ratchet Ratchets Lock washer Bolt Nut Flat washer Metal Nut washer Rubber Washers Metal washer BoltTransom Bottom Hull Flat-bottom hull Deep-vee hull Bolt Nut Trolling Motor Bracket InstallationInternal tooth washer Partial fish arches Transducer aimedShoot-Thru-Hull Preparation True bottom Second bottom Manual range setting Transducer location High speed Trolling speedShoot-Thru-Hull Installation Epoxy transducer to hull Speed/Temperature Sensors Transom Bottom of hull Power ConnectionsGood location Powering a Nmea 2000 Buss Nmea 2000 Power cable Page Power connections for the units in this series To Nmea To sonar Network port Units Network Socket Nmea 2000 Cable ConnectionsNmea 0183 Cable Connections Mounting the Unit Bracket, In-Dash or Portable Front 136 61.3 132 23.8 147.4 Millimeter Inch Inches 112 Cut on line 121Hole Diameter Other Accessories Page Basic Sonar Operation Memory MenusMain Menu Commands Sonar Menu Commands Pages Page Page Basic Sonar Quick Reference Sonar Operations Bait School Thermocline With fish Fish ArchesTo adjust sensitivity To Restore Factory Settings Important TipOther Free Training Aids Advanced Sonar Options & Other Features ASP Advanced Signal ProcessingAlarms To adjust and turn on the shallow alarmTo adjust and turn on the deep alarm To turn the fish alarm onCalibrate Speed Chart SpeedBacklight Level Grayline Contrast Thin or no Grayline Wider GraylineDepth Cursor Cursor line Depth boxDepth Range Manual To switch to Manual Depth RangeDepth Range Automatic To turn Auto Depth Range on againDepth Range Upper and Lower Limits Area zoomedFish I.D. Fish Symbols & Depths FasTrackPress ↓ to Fish ID Symbolsentexitexit FishTrackNoise Rejection Symbols with FishTrack depthsHyperScroll Overlay DataTo turn off displayed data Ping Speed & HyperScroll To change displayed data font sizeFrom the Sonar Page, press MENU↓ to Ping Speedent Reset Options Pop-up HelpSensitivity & Auto Sensitivity Reset Water DistanceScreen Contrast and Backlight Level Automatic Sensitivity Set Keel Offset Press MENUMENU↓ to SET Keel Offsetent Set LanguageSoftware Version Information Press MENUMENU↓ to Software Infoent Sonar Chart ModeSonar Page & Sonar Chart Display Options Split Zoom Sonar Chart Digital Data/Chart Stop Chart Sonar SimulatorSurface Clarity Units of Measure Press ↓ or ↑ to select clarity levelEXITEXITEXITZoom & Zoom Bar VolumeUpper and Lower Limits Zoom Pan Troubleshooting No fish arches when the Fish I.D. feature is off Noise Page Index Page Lowrance Electronics Full ONE-YEAR Warranty How to Obtain Service… Accessory Ordering Information for all countries Visit our web site