Lowrance electronic X52, X59DF manual 121, Hole Diameter, Inches 112 Cut on line

Page 32

Before positioning the bracket, be sure to hold the cables against the rear edge of the hole. Then, slide the bracket over the hole and butt the rear of the bracket base firmly against the cables, thus pinning them in place against the side of the hole. Finally, fasten the bracket to the dash. Attach the unit to the gimbal bracket using the supplied gimbal knobs and washers.

In-Dash Installation

You can mount the unit in the dash with an optional FM-4 In-Dash Adapter Kit. The kit includes mounting hardware, a template for cutting the hole and an instruction sheet, part 988-0147-44.

121

[4.76]

Top

	47
	[1.85]	In-Dash
		In-Dash
		Template
	Hole
	diameter	Millimeters
	3.5	Millimeters
	3.5	[Inches]	112
	[0.14]	[Inches]	112
	[0.14]		[4.40]
			[4.40]

Cut on line

ALWAYS VERIFY DIMENSIONS

R 6.35

[0.25] 119

[4.68]

In-dash mounting template for X52 and X59DF sonars, showing

dimensions. NOTE: The figure above is not printed to scale. A scaled

template is available for free download from our web site,

www.lowrance.com.

Portable Installation

Like many Lowrance products, this sonar unit is capable of portable operation by using an optional portable power pack. The power pack and an optional portable transducer expand the uses for your sonar unit. The power pack makes it easy to use the unit on your boat or take 28

Image 32

Contents X52 and X59DF Lowrance Electronics Inc 12000 E. Skelly Dr Tulsa, OK USA Table of Contents Fish I.D. Fish Symbols & Depths Capabilities and Specifications X52 and X59DF IntroductionFeet 244 meters at 200 kHz 1500 feet Transducer Installation PreparationsSingle-frequency transom installations Dual-frequency transom installationsSingle-frequency trolling motor installations Shoot-through hull installationsPad Deadrise less than Strakes Good location Poor location Location Poor angleTransom Transducer centerline Hull bottom Dot Ratchet Ratchets Lock washer Bolt Nut Flat washer Metal Nut washer Rubber Washers Metal washer BoltTransom Bottom Hull Flat-bottom hull Deep-vee hull Bolt Nut Trolling Motor Bracket InstallationInternal tooth washer Partial fish arches Transducer aimedShoot-Thru-Hull Preparation True bottom Second bottom Manual range setting Transducer location High speed Trolling speedShoot-Thru-Hull Installation Epoxy transducer to hull Speed/Temperature Sensors Transom Bottom of hull Power ConnectionsGood location Powering a Nmea 2000 Buss Nmea 2000 Power cable Page Power connections for the units in this series To Nmea To sonar Network port Units Network Socket Nmea 2000 Cable ConnectionsNmea 0183 Cable Connections Mounting the Unit Bracket, In-Dash or Portable Front 136 61.3 132 23.8 147.4 Millimeter Inch Inches 112 Cut on line 121Hole Diameter Other Accessories Page Basic Sonar Operation Memory MenusMain Menu Commands Sonar Menu Commands Pages Page Page Basic Sonar Quick Reference Sonar Operations Bait School Thermocline With fish Fish ArchesTo adjust sensitivity To Restore Factory Settings Important TipOther Free Training Aids Advanced Sonar Options & Other Features ASP Advanced Signal ProcessingAlarms To adjust and turn on the shallow alarmTo adjust and turn on the deep alarm To turn the fish alarm onCalibrate Speed Chart SpeedBacklight Level Grayline Contrast Thin or no Grayline Wider GraylineDepth Cursor Cursor line Depth boxTo switch to Manual Depth Range Depth Range AutomaticDepth Range Manual To turn Auto Depth Range on againDepth Range Upper and Lower Limits Area zoomedFish I.D. Fish Symbols & Depths FasTrackPress ↓ to Fish ID Symbolsentexitexit FishTrackSymbols with FishTrack depths HyperScrollNoise Rejection Overlay DataTo turn off displayed data Ping Speed & HyperScroll To change displayed data font sizeFrom the Sonar Page, press MENU↓ to Ping Speedent Reset Options Pop-up HelpSensitivity & Auto Sensitivity Reset Water DistanceScreen Contrast and Backlight Level Automatic Sensitivity Set Keel Offset Press MENUMENU↓ to SET Keel Offsetent Set LanguageSoftware Version Information Press MENUMENU↓ to Software Infoent Sonar Chart ModeSonar Page & Sonar Chart Display Options Split Zoom Sonar Chart Digital Data/Chart Stop Chart Sonar SimulatorSurface Clarity Units of Measure Press ↓ or ↑ to select clarity levelEXITEXITEXITZoom & Zoom Bar VolumeUpper and Lower Limits Zoom Pan Troubleshooting No fish arches when the Fish I.D. feature is off Noise Page Index Page Lowrance Electronics Full ONE-YEAR Warranty How to Obtain Service… Accessory Ordering Information for all countries Visit our web site