Lowrance electronic X59DF, X52 manual Important Tip, To Restore Factory Settings

Page 45

NOTE:

If you want to change the sensitivity in Manual Mode, first turn off Auto Sensitivity: from the Sonar Page, press MENUto AUTO SENSITIVITYENTto SENSITIVITYENT. Press or to pick a different sensitivity setting. When it's set at the desired level, press EXIT.

Important Tip:

While you are experimenting and learning, it's possible to scramble the settings so that the sonar picture disappears from your screen. If that happens, remember that it's easy to switch back to full automatic operation by simply restoring the factory auto settings. Here's how:

To Restore Factory Settings

1.Press MENUMENUto RESET OPTIONSENT.

2.The unit asks if you want to reset all the options. Press or to YESENT. All options are reset, and the unit reverts back to the original settings.

Fish Symbols vs. Full Sonar Chart

You may have noticed in the quick reference that we used fish arches in full sonar chart mode for our example, and not the popular Fish I.D.fish symbol feature. Here's why.

Fish I.D. is an easier way for a sonar novice to recognize a fishy signal return when he sees it. However, locating fish by symbol only has some limitations.

Your sonar unit's microprocessor is remarkably powerful, but it can be fooled. Some of the echoes calculated to be fish could be tree limbs or turtles! To see what's under your boat in maximum detail, we recommend you turn off Fish I.D. and begin learning to interpret fish arches.

Fish I.D. is most handy when you're in another part of the boat or performing some task that prevents you from watching the sonar screen. Then, you can turn on Fish I.D. and the audible fish alarm. When that lunker swims under your boat, you'll hear it!

Fish I.D. can also be useful when you want to screen out some of the sonar detail gathered by your unit. For example, in one case fishermen in San Francisco Bay saw clouds of clutter in the water but no fish arches. When a down rigger was pulled up, it brought up several small jellyfish. The fishermen switched their Lowrance sonar to Fish I.D., which screened out the schools of jellyfish and clearly showed the game fish there as fish symbols.

41

Image 45
Contents X52 and X59DF Lowrance Electronics Inc 12000 E. Skelly Dr Tulsa, OK USA Table of Contents Fish I.D. Fish Symbols & Depths Introduction Capabilities and Specifications X52 and X59DFFeet 244 meters at 200 kHz 1500 feet Preparations Transducer InstallationDual-frequency transom installations Single-frequency transom installationsSingle-frequency trolling motor installations Shoot-through hull installationsGood location Poor location Location Poor angle Pad Deadrise less than StrakesTransom Transducer centerline Hull bottom Dot Ratchet Ratchets Metal Nut washer Rubber Washers Metal washer Bolt Lock washer Bolt Nut Flat washerTransom Bottom Hull Flat-bottom hull Deep-vee hull Trolling Motor Bracket Installation Internal tooth washerBolt Nut Transducer aimed Partial fish archesShoot-Thru-Hull Preparation Transducer location High speed Trolling speed True bottom Second bottom Manual range settingShoot-Thru-Hull Installation Epoxy transducer to hull Speed/Temperature Sensors Power Connections Good locationTransom Bottom of hull Powering a Nmea 2000 Buss Nmea 2000 Power cable Page Power connections for the units in this series Nmea 2000 Cable Connections Nmea 0183 Cable ConnectionsTo Nmea To sonar Network port Units Network Socket Mounting the Unit Bracket, In-Dash or Portable Front 136 61.3 132 23.8 147.4 Millimeter Inch 121 Hole DiameterInches 112 Cut on line Other Accessories Page Basic Sonar Operation Menus MemoryMain Menu Commands Sonar Menu Commands Pages Page Page Basic Sonar Quick Reference Bait School Thermocline With fish Fish Arches Sonar OperationsTo adjust sensitivity Important Tip To Restore Factory SettingsOther Free Training Aids ASP Advanced Signal Processing Advanced Sonar Options & Other FeaturesTo adjust and turn on the shallow alarm AlarmsTo turn the fish alarm on To adjust and turn on the deep alarmChart Speed Backlight LevelCalibrate Speed Grayline Thin or no Grayline Wider Grayline ContrastCursor line Depth box Depth CursorDepth Range Automatic To switch to Manual Depth RangeDepth Range Manual To turn Auto Depth Range on againArea zoomed Depth Range Upper and Lower LimitsFasTrack Fish I.D. Fish Symbols & DepthsFishTrack Press ↓ to Fish ID SymbolsentexitexitHyperScroll Symbols with FishTrack depthsNoise Rejection Overlay DataTo turn off displayed data To change displayed data font size Ping Speed & HyperScrollFrom the Sonar Page, press MENU↓ to Ping Speedent Pop-up Help Reset OptionsReset Water Distance Screen Contrast and Backlight LevelSensitivity & Auto Sensitivity Automatic Sensitivity Set Keel Offset Set Language Software Version InformationPress MENUMENU↓ to SET Keel Offsetent Sonar Chart Mode Sonar Page & Sonar Chart Display OptionsPress MENUMENU↓ to Software Infoent Split Zoom Sonar Chart Digital Data/Chart Sonar Simulator Stop ChartSurface Clarity Press ↓ or ↑ to select clarity levelEXITEXITEXIT Units of MeasureVolume Upper and Lower LimitsZoom & Zoom Bar Zoom Pan Troubleshooting No fish arches when the Fish I.D. feature is off Noise Page Index Page Lowrance Electronics Full ONE-YEAR Warranty How to Obtain Service… Accessory Ordering Information for all countries Visit our web site