Panasonic manual Before use, AG-MX70 connections, Installation of the USB driver

Page 77

Before use

AG-MX70 connections

It is necessary to connect the PC to the AG-MX70 using the USB cable before installing the software. Follow the steps below.

1)Turn off the power to the AG-MX70.

2)Connect the PC to the AG-MX70 using the USB cable.

Insert the USB cable connectors into the corresponding USB ports on the PC and on the rear panel of the AG-MX70.

This completes the connection. When the 2 units are being connected for the first time, install the USB driver by following the steps in “Installation of USB driver” below.

<Note>

The USB cable is not supplied with this unit. Use a commercially available 3 m or shorter USB cable. Note that if the cable to be used is more than 3 m in length, communications may not be performed correctly.

Installation of the USB driver

It is necessary to install this driver in the PC to enable USB communications between the PC and AG-MX70 after they are connected for the first time. (It is only necessary to install the USB driver software once.) Follow the steps below.

∫For Windows 98 and Windows 2000 <Notes>

≥ The steps outlined below are for Windows 98.With Windows 2000, the screens will differ slightly, but the driver software can still be installed following the same steps.

≥ Be sure to log on as a user with Administrator rights when installing this software in a PC with Windows 2000.

1)Connect the PC to the AG-MX70 correctly.

2)Turn on the power to the PC. Check that Windows has started up.

3)Place the setup CD-ROM in the PC’s CD-ROM drive.

4)Turn on the power to the AG-MX70.

After a short while, the “Add New Hardware Wizard” dialog will be displayed.

5)Click on the “Next” button.

6)Select “Search for the best driver for your device,” then click on the “Next” button.

7)Place a check next to “Specify a location,” enter the USB_DRV folder in the setup CD-ROM as the search location and click on the “Next” button.

8)If the driver is searched correctly, a screen similar to the one shown below will be displayed.

9)When the screen indicating that the installation is complete is displayed, click on the “Finish” button.

77

Image 77

Contents AG- P FCC Note Overview Contents About this software SpecificationsOverview of MX-Navi Processing of image data Before useParts and their functions ONE WAY button REV reverse buttonMIX button LUM luminance key buttonPreset bus / Still execution button Preset bus selector buttonPreset bus / Strobe execution button Preset bus / Video Effects execution ButtonSetting page display area Item, parameter setting areaJoystick, Z parameter display area Audio level meterINT Video internal video setting Display button SET UP initial setting page display buttonAudio Effects audio effect setting Display button Audio Effects on audio effect Execution buttonTime time setting rotary control Phone headphone volume controlPattern transition/key pattern number Setting button ME ME transition/key transition time setting buttonPreset / Source 1/5 selector button 1SHIFT key 9B/PRESET / Source 4/8 selector buttonPreset / Source 2/6 selector button Preset / Source 3/7 selector buttonSource 2/6 fader 1SOURCE 1/5 fader 4SOURCE 4/8 faderSource 3/7 fader AUX 1 faderMIC input connector External key input connectorExternal input Y connector External input PB connector= ? Editor interface connector 9-pin Analog audio 3 input connectorsTally output connector RS-422A/RS-232C selector switch≥ Functions that can be controlled from the AG-A850 External interfaces≥ Connections ≥ Connection of conversion cableExample 2 Live application System DiagramExample 1 Live application Example 3 Editing application CD player, etc PC with MX-Navi already installedVideo camera Editing controllerSetting panel screen Power supply and backupINTVideo internal video setting screen 00EWhen Custom1, 2 has been selected When Back Matte has been selectedBack Color Level Pattern Grade Matte White 255 Black Color Set Pattern Matte Custom1 BackMWhen Frame = When Memory has been selectedMemory Frame Mode When FrameColor Effect Gain 128 Color Effects setting screen00 E 1000 F 3015 1000F Video Effects setting screenPos 128 Channel display Scrolled displayDefocus setting Mosaic settingMono monochrome setting Mosaic Size Off Defocus LevelTime Screen Effects Still Field 10F Time Effects still/strobe settingPaint setting Decay settingNega negative setting Mirror setting Decay Time Off Paint Level Nega3D setting Video Effects setting screen Execution of Effects Preset program transmissionAB transition DSK key1000 F 0013 Wht Effect-by-effect setting screensTransition wipe pattern settings Pattern Width Color Edge Hard White Pattern Edge settingEffects Light Off Effects settingEffects Light Shadow Effects Time Light Trail SelfKey setting Pos 128 196 Chroma Key setting00E 1000F 3101 Wht Key Slice Slope Level 128 255Crop setting Color Offset Slice Area Mono L Cancel Color cancel settingBorder setting Crop00E 1000F 3102 Wht Luminance Key and EXT Key external key settingsKey setting Pos 128 00E 1000F 9501 Title Key settingKey setting 00E 1000F 3002 Basic Pattern Key setting numbers 3001 to1000F 3301 Wht Other key settings numbers 3301 and up3Dmodify setting Effect-by-effect setting screens Empty Modify 9000 Setup Key Learn settingFrame Level Copy 255 Paste Rotate Time TransF Exit 128 00 E 1000 F 3013Frame Level Copy 255 Paste Width Angle Time Amp Exit 192 With flag #6002 Insert Replace FlagWith accordion #6003 Insert Replace Frame Level Copy 255 Paste Width Angle Amp Exit 192Pattern number selected Processing after cancel operation 00E 1000F DSK/Fade settingsDSK Source settings DSK On/Off setting DSK Key settingsCrop setting Fade Audio Phone Black After White Off Pre Blue Fade settingsPAN setting Audio Effects settings00E 1000F Wht BalanceEQ Mid equalizer midrange setting EQ equalizer settingVoice Change voice changer setting Mute settingWash Ph 128 Pr 196 Setup initial setting screen1000F 3015 Wht Direct Pattern setting Power power on setting00 E 1000 F Wht 00 E 1000 F 3015 WhtExample of transition Pos 128 196 Example of key pattern Pos 128 Y 196Factory settings Audio Input Video Setup Default Link Audio Video Input settingsSetting method 3015 WhtVideo Format setting Memory settingGen Lock external synchronization setting Bus setting System1 settingSystem2 setting File setting Audio Level settingSetting method Other settingsRecall method Clearing eventsNumber key priorities Correlation between number key settings and Pattern buttonTransition time selection Pair Transition patterns100 101 102 DVE CUT SAT MIX 1301 1302 1303 1304 1305 1306 1307 1308 139 140 MIX 3D DVE LUM Key patterns3305 Exp 3315 4701 4702 4703 4704 4705 4706 4707 4708 4730 4731 4732 4733 4769 4770 4771 4772 4773 +Diss 4789 4790 4791 4792 4793 28 T-29 T-30 10 T-11 T-129711 9721 9731 14 T-15 17 T-18 T-19 22 T-23 T-24Overview of MX-Navi About this softwareUSB driver MX-NaviProcessing of image data ≥ Memory capacity Management of the image memoryBefore use Installation of the USB driverAG-MX70 connections For Windows 98 and Windows 2000 NotesFor Windows XP Note Operation confirmation Installation of MX-NaviScreen descriptions Startup and shutdownIcon 9NAME/COMMENT Edit menu Menu descriptionsFile menu Cursor menu View menuHelp menu Operation menuTool menu Title data operations Setting the Title data playback propertiesFlow until Title data playback Registering Title data in the transmission list≥ Effect Clearing Title data Manual transmission and playback of Title dataAutomatic transmission and playback of Title data Reordering the transmission list Checking the Title data imageSaving the transmission list Opening a transmission listChecking the memory status of the AG-MX70 Changing the AG-MX-70 memory settingsOther operations Clearing IntVideo data Transmission and playback of IntVideo dataSaving data Recalling eventsStill Duration Setting the initial propertiesMovie Duration Roll SpeedBoot and shutdown Setting the operating environmentMemory management File ManagementLeft arrow List of short-cut keysDown arrow Open the properties of the selected dataProblem What to check Before calling for service≥Update the video card driver to the newest version General SpecificationsVideo INPUT/OUTPUT Accessories Installation of the AG-YA70 AG-VE70 Installation of the AG-VE70Panasonic Broadcast & Television Systems Company

Related manuals

Manual 6 pages 29.07 Kb