JVC KM-H3000U, KM-H2500U, KM-H3000E manual IP Address, To configure the Clean Feed output

Page 17

1.Press MENU.

2.Press the SYSTEM Wipe Pattern button.

3.Press the Analog Out knob to display the Analog Out menu.

4.Use the AnOut knob to select the source. You can choose from the following:

•Prview — Preview bus output.

•Progrm — Program bus output.

•Aux 1 - 3 — Aux bus 1-3 outputs.

•In 1 - 12 — Inputs 1-12 (KM-H3000 only).

•In 1 - 6 — Inputs 1-6 (KM-H2500 only).

5.Use the AnMode knob to set the appearance of the analog output. You can choose from the following:

•Full — Full screen display.

•LtrBox — Letter box display.

Note:

•If your switcher is operating in a 4:3 aspect ratio, you can not set the analog output to letter box.

Clean Feed

The Clean Feed output provides a second program output that is derived from a different location than the standard program output. Using the Clean Feed allows you to remove particular keys without affecting the primary program output. Typical applications are:

•Multilingual and live-to-tape productions

•Recording call-in shows for later airing without telephone numbers displayed

To configure the Clean Feed output:

2

1

3

 

1.Press MENU.

2.Press the SYSTEM Wipe Pattern button.

3.Use the CLEAN knob to select where in the output stream the Clean Feed is derived. You can choose from the following:

•Key 1 — Clean Feed output is taken before any keys are added.

•Key 2 — Clean Feed output is taken after Key 1 but before Key 2 or 3 is added.

•Key 3 — (KM-H3000 only) Clean Feed output is taken after Key 1 and 2 but before Key 3 is added.

IP Address

The switcher is equipped with an Ethernet port to allow remote access. By default, the switcher uses DHCP to automatically obtain an IP address. You can manually set an IP address, network mask, and default gateway if your network does not have a DHCP server.

Note:

•You do not need to connect your switcher to a network for it to function.

To configure a DHCP IP address for your switcher:

3

2

6

5

 

4

1.Ensure your switcher is connected to your network via the ethernet port.

2.Press MENU.

3.Press the SYSTEM Wipe Pattern button.

4.Press NEXT until IP Addr is displayed.

5.Press the IP Addr knob to display the IP Address menu.

6.Use the IPMode knob to select DHCP.

7.Press the IPMode knob to enter the selection.

8.Press the Confrm knob to commit the change. Press the Cancel knob to discard the change and return to the previous setting.

11

Page 16 Page 18
Image 17
Page 16 Page 18
Contents KM-H2500E/U KM-H3000E/U Important Regulatory and Safety Notices Safety Precautions Environmental Information Contents Introduction Advanced Operation Page Documentation Terms About This ManualAbbreviations Control Panel OverviewControl Panel Rear Connections Overview To access a menu using the Menu buttonMenu System Menu Navigation Installing Your Own Insert FilmsKnobs ButtonsFader ShiftTransitions PositionerReference Type Switcher Video FormatEuropean Video Formats North American Video FormatsTo assign an Fcfs channel Assigning Fcfs ChannelsFormat Conversions for Bus Mode Format Conversions for Input ModeTo set the output reference sync Setting the Output Reference SyncOutput Reference Sync Ancillary Data Resetting the Output Reference SyncAspect Ratio Default Alpha Channel Mappings Input BNC ConfigurationOutput Configuration To configure the Clean Feed output Clean FeedTo configure a Dhcp IP address for your switcher IP AddressCustomizing the Panel Glow Switcher PersonalityAux Bus Memory Recalls Loading Color Schemes Power-Save ModeSaving Color Schemes Resource Sharing Transition Rate UnitsDouble-Press Rate Next Transition Area Reset Switch on Field or FrameEditor Control Transition Resume DirectionTo set the Next Transition Key behavior Next Transition Key BehaviorTo set the transition resume direction Cutting on the Program Bus Transition OverviewTo perform a transition KEYPausing a Transition Configuring the Auto Trans RateWipe Transitions Keying OverviewKey Transitions Video LayeringSelecting Keys Performing Key TransitionsChroma Key Setting the Transition Rate for Dedicated Key TransitionsDedicated Key Transitions Using other Adjustments Using a MatteMattes Selecting a Matte ColorTo fade to black To apply other adjustmentsFade to Black Choosing a Memory Access Mode Using the Memory SystemStoring Memory Registers Recalling Memory RegistersMemory AI and Recall to Preview Bus HoldMemory AI and Keys Memory AI and Recall to Preview ExamplesTransition Limit To set the Recall to Preview modeRecall to Preview On Memory AIConfiguring Default Settings Reset OptionsTo Quickly Reset the Transition Limit To configure user-defined defaultsResetting the Switcher Restoring Default Settings to Factory StateResetting Individual Settings Shared ParametersRestoring to Factory Defaults Resetting Menu ItemsUSB Storage Saving Memory Banks and RegistersTo upgrade the switcher software Software UpgradesPress Next until Run Software Upgrade From USB is displayed Loading Memory Banks and RegistersModifying Keys Completing a Software UpgradeAdvanced Keying Chroma Key Fine Tuning To modify the appearance of a Split Key Modifying Split KeysSplit Keys Modifying Wipes Accessing the Aux BusesAux Buses To modify time and directionSelecting a Source for the Aux Buses TalliesEditor Port General Purpose Interface GPISupported Editors Pin TriggerPage File Formats Media-Store OverviewTransparency Loading an Image or Animation by BrowsingEntering Media Numbers Understanding Media NumbersLoading an Image or Animation by Media Number To lock or unlock place and bank valuesTo change an image between shaped and unshaped Modifying Media-Store Image AttributesTo modify the position of a Media-Store image Saving and Reverting Attributes Modifying Animation PlaybackAnimation Control To revert to saved attribute values To save attributes for an imagePage Weight DimensionsPower Requirements HD-SDI Input and Output SpecificationsGVG100 Protocol Supported Commands Error MessagesSwitcher Error Messages GVG100 Supported CommandsLast 5 bits used bit 0 is GVG100 Supported Lamps GVG100 Supported Analog ControlsName MLE/Keyer Byte Code GVG100 Supported Buttons GVG100 Supported Buttons Page 多格式数字高清切换台

KM-H2500, KM-H2500U, KM-H3000U, KM-H2500E, KM-H3000E specifications

The JVC KM-H3000E, KM-H2500E, KM-H3000U, KM-H2500U, and KM-H2500 are professional video production switchers designed to meet the demands of live broadcasting, events, and production environments. These switchers are renowned for their robust construction, intuitive operation, and advanced features that cater to a wide range of workflow requirements.

The KM-H3000E and KM-H3000U are high-end models, offering extensive capabilities for complex productions. Both units feature a 1 M/E switcher configuration, enabling seamless switching between multiple video sources. The KM-H3000 series supports HD and SD formats, ensuring compatibility with various input signals. One of its significant characteristics includes a large-scale multi-viewer output, which provides operators with the ability to monitor multiple sources on a single screen, enhancing the efficiency of live production.

In terms of connectivity, the KM-H3000 series equipped with extensive I/O options, allowing for flexible integration with other broadcast equipment. It also supports external keyers, picture-in-picture effects, and advanced chroma keying, creating dynamic live content that captivates audiences. Additionally, the user interface is designed for quick and intuitive operation, featuring customizable buttons and clear labeling that streamline the switching process.

On the other hand, the KM-H2500E and KM-H2500U serve as mid-range alternatives, suitable for smaller operations without compromising functionality. These models maintain a compact design while still offering an impressive array of features. The KM-H2500 series includes 1 M/E switcher capabilities and supports multiple HD/SD formats, similar to its higher-end counterpart, but with slightly reduced input options.

One notable feature of the KM-H2500 is its cost-effectiveness, making it an attractive choice for educational institutions, small production houses, and local broadcasters. It supports simple transitions, effects, and basic keying, enabling users to produce quality content without the complexity of more advanced systems.

In summary, JVC's KM-H series offers versatile solutions for video production, whether it's high-end broadcasting or smaller-scale operations. With their robust feature sets, ease of use, and flexible connectivity, the KM-H3000E, KM-H2500E, KM-H3000U, KM-H2500U, and KM-H2500 are exceptional choices for any production environment. These switchers exemplify JVC's commitment to quality and innovation in the realm of professional video equipment.
Top Page Image Contents