JVC KM-H3000U, KM-H2500 manual To save attributes for an image, To revert to saved attribute values

Page 47

To save attributes for an image:

2

1.Modify the attributes for an image as necessary

2.Use the Func knob to save the attributes for that image. You can choose from the following:

•Save — Saves the currently displayed attribute. Other saved attributes are not affected.

•SavAll — Saves all attributes.

To revert to saved attribute values:

4

3

2

1

1.Press and hold SHIFT on any bus. If you use the Program bus or on-air Key bus, you will affect on-air images.

2.Press MEDIA 1 or MEDIA 2 to select the Media-Store channel to load the image into.

3.Press NEXT until Attrib is displayed.

4.Use the Func knob to save the attributes for that image. You can choose from the following:

•Revert — Reverts the currently displayed attribute to the previously saved value. Other attributes are not affected.

•RevAll — Reverts all attributes to previously saved values.

41

Image 47

Contents

KM-H2500E/U KM-H3000E/U Important Regulatory and Safety Notices Safety Precautions Environmental Information Contents Introduction Advanced Operation Page Control Panel Overview About This ManualDocumentation Terms AbbreviationsControl Panel Rear Connections Overview To access a menu using the Menu buttonMenu System Buttons Installing Your Own Insert FilmsMenu Navigation KnobsPositioner ShiftFader TransitionsNorth American Video Formats Switcher Video FormatReference Type European Video FormatsTo assign an Fcfs channel Assigning Fcfs ChannelsFormat Conversions for Bus Mode Format Conversions for Input ModeTo set the output reference sync Setting the Output Reference SyncOutput Reference Sync Ancillary Data Resetting the Output Reference SyncAspect Ratio Default Alpha Channel Mappings Input BNC ConfigurationOutput Configuration IP Address Clean FeedTo configure the Clean Feed output To configure a Dhcp IP address for your switcherCustomizing the Panel Glow Switcher PersonalityAux Bus Memory Recalls Loading Color Schemes Power-Save ModeSaving Color Schemes Resource Sharing Transition Rate UnitsDouble-Press Rate Transition Resume Direction Switch on Field or FrameNext Transition Area Reset Editor ControlTo set the Next Transition Key behavior Next Transition Key BehaviorTo set the transition resume direction KEY Transition OverviewCutting on the Program Bus To perform a transitionKeying Overview Configuring the Auto Trans RatePausing a Transition Wipe TransitionsPerforming Key Transitions Video LayeringKey Transitions Selecting KeysChroma Key Setting the Transition Rate for Dedicated Key TransitionsDedicated Key Transitions Selecting a Matte Color Using a MatteUsing other Adjustments MattesTo fade to black To apply other adjustmentsFade to Black Recalling Memory Registers Using the Memory SystemChoosing a Memory Access Mode Storing Memory RegistersMemory AI and Recall to Preview Examples Bus HoldMemory AI and Recall to Preview Memory AI and KeysMemory AI To set the Recall to Preview modeTransition Limit Recall to Preview OnTo configure user-defined defaults Reset OptionsConfiguring Default Settings To Quickly Reset the Transition LimitShared Parameters Restoring Default Settings to Factory StateResetting the Switcher Resetting Individual SettingsSaving Memory Banks and Registers Resetting Menu ItemsRestoring to Factory Defaults USB StorageLoading Memory Banks and Registers Software UpgradesTo upgrade the switcher software Press Next until Run Software Upgrade From USB is displayedModifying Keys Completing a Software UpgradeAdvanced Keying Chroma Key Fine Tuning To modify the appearance of a Split Key Modifying Split KeysSplit Keys To modify time and direction Accessing the Aux BusesModifying Wipes Aux BusesSelecting a Source for the Aux Buses TalliesPin Trigger General Purpose Interface GPIEditor Port Supported EditorsPage Loading an Image or Animation by Browsing Media-Store Overview File Formats TransparencyTo lock or unlock place and bank values Understanding Media NumbersEntering Media Numbers Loading an Image or Animation by Media NumberTo change an image between shaped and unshaped Modifying Media-Store Image AttributesTo modify the position of a Media-Store image Saving and Reverting Attributes Modifying Animation PlaybackAnimation Control To revert to saved attribute values To save attributes for an imagePage HD-SDI Input and Output Specifications DimensionsWeight Power RequirementsGVG100 Supported Commands Error MessagesGVG100 Protocol Supported Commands Switcher Error MessagesLast 5 bits used bit 0 is GVG100 Supported Lamps GVG100 Supported Analog ControlsName MLE/Keyer Byte Code GVG100 Supported Buttons GVG100 Supported Buttons Page 多格式数字高清切换台